bosch table saw 3d models

This is a replacement wheel for the Bosch table saw. The original had its center half-circle hole worn out. ...

My trusty portable Bosch table saw comes equipped with a port that allows me to connect a ShopVac duct, but I encountered some trouble linking them up, so I created this adaptor. ... Print Settings Printer Brand: Prusa Rafts: No Supports: No...

... Additional information about this project can be found on my blog at https://makeverse.home.blog and specifically at https://makeverse.home.blog/2019/03/02/featherboard-for-bosch-pts10-table-saw/. ... I hope you find it enjoyable.

Here is my first version of glide pad replacement for the rip fence of the table saw 4100. Not perfect, but work on my rip fence. ... part number # 2610950101

Customized version of https://www.thingiverse.com/thing:1246651 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1246651

The nut from the original post was too big for my saw so I redesigned one based on the dimensions of the miter slot on my saw.After that I decided that the featherboard itself was a bit short so I lenghtened it by 5mm. I also increased the diameter...

I designed this miter bar because the one included with the saw has too much play. The aluminium miter slot is 21mm (when new) but will wear down with use and it will wear more at the front than the...

<p>This is a simple ring adapter.</p> <p>Outside Diameter is 57mm (fits the 2.25inch hole)</p> <p>Inside diameter is 45.4mm (fits the 1.75inch Ridgid hose end)</p> <p>It's about 31mm in length</p> <p>I printed this with 30% infill and came out fairly...

This is a simple ring adapter. Outside Diameter is 57mm (fits the 2.25inch hole) Inside diameter is 45.4mm (fits the 1.75inch Ridgid hose end) It's about 31mm in length I printed this with 30% infill and came out fairly rigid. Had to...

Exhaust air adapter for 50 millimeter exhaust hose

Dyson adapter for DC32 or similar to Bosch PTS10 table saw. Fits into the standard dust collection. ... I did not create the Dyson standard nose on it (like usual) in order to allow hose rotation, which makes connecting and disconnecting a lot faster...

INSERT PLATE for the Bosch PTS 10 Table Saw in 2 parts that can be printed on most 3D printers.

Diagram showing the measurements of the runners, and the T-slot in the table saw bed are shown in the pictures. ... The runners protrude slightly above the level of the bed to allow the sled to move, so don't use these for featherboard locks (as they...

Insert the original plate into your Bosch PTS 10 as it was initially installed.

This is a zero clearance insert for the Bosch GTS10XC table saw. The model has already an opening for the riving knife to pass trough. As the model is too big to be printed as a whole on most printers, a 2-part model is also provided. I used...

Modelled to fit the Bosch GTS 10J Table Saw T-slot, should also fit the GTS XC. Made to fit a specifc featherloc's screw down clamps, because the stock part was the wrong size of the Bosch T-Slot. The part fits flush to the table bed, meaning when...

Use M6 screws

T-Slot Runners perfectly match Bosch GTS 10 XC and likely 4100 Table Saws. They fit snugly on my saw. ...A version features countersunk holes ideal for wood screws up to 4.5mm in diameter, while another lacks holes altogether.

Mounting Plate for the Bosch Router GKF12v-8 that I have attached to my table saw. ... The "Assembly.step" shows all the parts including vacuum hose and dummy for the router.

To fit a Bosch Professional GAS 35 dust collector to my Bosch Professional GTS 10J table saw.

In order to collect all the saw dust from my GTS 10J table saw I created a dust collection hood, in combination with the 4-way valve I created earlier (https://www.thingiverse.com/thing:6447210). ...Now I can balance the suction power between the hood...

Sliding block remade fitting for GTS 18V-216. ... Feather Board: https://www.thingiverse.com/thing:4040187 Nut handle: https://www.thingiverse.com/thing:361072 Needs 2x M6 Nut and 2x M6 Screw 30mm or longer

A simple measurement gauge holder checks the parallelism of saw blades and t-nuts or fence and t-nut or whatever with a t-nut. The Fusion 360 file is attached for the measurement gauge, which has a 3.5mm distance between the back wall of the body...

Here is a Table Saw to Vacuum Cleaner Adapter for Bosch Professional GTS 635-216.

This is my take on a Table Mount for the Jigsaw to convert it to a kiiinda scrollsaw/bandsaw. Only the left bracket is uploaded, flip it to get the right bracket. ... The fusion 360 design files are also attached: https://a360.co/34gt3I1

Holes are for M4 or 3.5-4mm wood screw.

Adapting Bosch's table saw to seamlessly integrate with Rigid's powerful vacuum, this versatile attachment fits precision onto the saw's original adapter, ensuring a rock-solid connection that enhances work efficiency.

This custom holder is specifically designed to securely store the green mini Bosch Circular Saw, with its compact design allowing it to potentially accommodate the blue model as well. Since both batteries employ identical sliding mechanisms,...