bosch miter saw dust collector 3d models

Miter Saw

It's a very tight fit on both the vacuum and the miter saw, though they are not going anywhere. I used some paracord to support the vacuum hose, just to lessen the chance the hose will pop off. Printed with 10% infill, a .6mm nozzle, and .35mm layer...

Dust collection is not good with this or any miter saw I have used. Without the Dust Shroud, it is virtually non-existent. This part deteriorates over time and breaks into small pieces. ... I modeled this one to be close to the original in design....

This file creates an adapter that enables a miter saw dust port to be connected with a shop-vac. It was specifically designed for the Ryobi 12” Sliding Compound Miter Saw with Laser TSS120L and the Shop-Vac 90M300. The adapter may also work with...

This file creates a converter that enables the connection of a miter saw dust port to a shop vacuum. It was specifically developed for use with the Ryobi 12” Sliding Compound Miter Saw with Laser TSS120L and the Shop-Vac 90M300. Although it may...

... smaller shop space. Tested on these specific models: Vacuum: https://www.lowes.com/pd/Shop-Vac-12-Gallon-6-HP-Portable-Wet-Dry-Shop-Vacuum/1001435286 Saw: https://www.lowes.com/pd/DEWALT-12-in-15-Amp-Dual-Bevel-Sliding-Compound-Miter-Saw/1000145735

Model 36-255L (may fit other models) 12” COMPOUND MITER SAW This saw is discontinued and this part can no longer be ordered. Dust collection is not good with this or any miter saw I have used. ...Without the Dust Shroud, it is virtually non-existent....

My dad got a “dust funnel” broken on his Einhell pull crosscut saw 2354. I have the small version, but the rod funnel is identical. So I designed the part for print. It ensures that the saw dust is directed into the catch bag. Printed in PLA for now...

This print will convert the oval dust port to fit over a 1" vacuum hose (1.25" OD on the hose). ...&nbsp;The model was designed using imperial units, so you may have to convert to inches, depending on the slicer you are using.</p><p>&nbsp;</p>

A mobil miter for handsaws. ...The bottom of the miter is taped with high-friction rubber-tape. You can use it for sawing rectangular, square or round wood strips. ... If you like my designs, you can support me via paypal/me

To fit a Bosch Professional GAS 35 dust collector to my Bosch Professional GKT 55GCE circular saw.

To fit a Bosch Professional GAS 35 dust collector to my Bosch Professional GTS 10J table saw.

The base of the saw is secured with a strip of high-friction rubber tape. You can use it to cut rectangular, square or circular wood strips with ease. ... Print Settings Rafts: No Supports: No Resolution: 0.15mm Infill: 0% Notes: Wall thickness:...

Customized version of https://www.thingiverse.com/thing:1246651 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1246651

Adapter to connect Bosch C35 hose (gas 18v-10) to a cyclone dust collector with 50mm hole diameter.

Don't get your wife upset while making a hole in the wall! Print this part, attach it to your vacuum cleaner, and drill with precision and cleanliness. Make sure to use some supports in the center hole, as the rest should be fine. ...The internal...

Dust collector for bosch ra1161 router base. Attached using 3M double sided adhesive but the base of the print is large enough to allow the user to mark and drill holes that line up with the threaded holes on the router base, if you wanted to mount...

This dust extractor for the Bosch POF 1400 ACE makes use of the mounting points for the fence. Two 8mm rods of ~250mm are press fit in the holes. Good friction fit on Festool dust extraction hoses. ... Onshape document:...

An adapter for a DeWalt Mitre saw's dust bag was requested by my friend. He bought a collecting bag from E-Bay, but the exhaust outlet pipe and dust bag inlet pipe were slightly different sizes (1.522" and 1.527"). I designed both connectors using...

03/24/2020 NOTE: I originally printed this with PLA but the part eventually failed due to stress-related layer separation after 13 months of use and hundreds of removals/reinsertions of the dust hose into the connector. I then reprinted the part in...

This is a remix of ShapeLabs's track saw hose deflector design, which was then updated by Mak-E-Verse and made compatible for Makita tracks/rail guides. Both original designs are based off of the Festool FS-AW available for their rail guides. I...

Connects a shop vacuum hose to the guard of the radial arm saw, replacing the cast swiveling discharge elbow. The inlet side has a groove to accommodate the set screws that retain the original. They can be left slightly loose to allow the new elbow...

This is a remix of ShapeLabs's track saw hose deflector design, which was then updated by Mak-E-Verse and made compatible for Makita tracks/rail guides. Both original designs are based off of the Festool FS-AW available for their rail guides. ...I...

In order to create a very stable connection, I used four components:Two 3D printed parts (the adapter and a support block)A spare 5mm Allen key cut to a length of about 70mmPlastic tie strapsAdapter assembly (see notes on pictures for further...

Dust collector adapter for Bosch GTS 10XC to Bosch Click & Clean / Kärcher C35.

An adapter for the Bosch Glide Saw (GCM12SD) to a Rockler Dust Right 4" tool port This re-uses the red composite ring from the original dust collection bag that comes with the saw. Simply remove the ring and place it onto the printed adapter. I...

Link to saw:...

In order to collect all the saw dust from my GTS 10J table saw I created a dust collection hood, in combination with the 4-way valve I created earlier (https://www.thingiverse.com/thing:6447210). ...Now I can balance the suction power between the hood...