bosch miter saw dust collection 3d models

This is a replacement clip for the rubber dust collector on the Festool sliding compound miter saw.  It’s designed for the Kapex KS 120 EB model, but looks like it could fit other models as well.

2.5 in Drill Press Dust collection device.

dust collection for pegas scrollsaw 16" requires 4x screw M4x14

Durable 2-1/4 inch Dust Collection Duct Connectors

Bosch Handle for Reciprocating Saw Blades Requires a Specific Fastener Combination. ...To Assemble This Component, You Need to Acquire an M3x20 Bolt and Its Corresponding Nut.

... ...(Pre Airlock) Adapter fit ⌀35mm standard accessory vacuum cleaner such as Kärcher A 2004 and for example DeWalt DW770 mitre saw with ⌀28mm dust collector. Requires a (F-23) o-ring in the grove for a tight seal on the saw side of the adapter. ...

Miter Bar Fence Clamp for a Ryobi BT-3000 or BT-3100 Table Saw. Requires a 3-inch-long, 3/8 inch bolt and nut. ...Since the original product has been discontinued by Ryobi, I had to find an alternative solution.

Added more options for dimensions to vacuum adapter created by other user. ... Turns out that the 1-7/8" Ridgid vacuum hose is more like 1-13/16", and my Metabo miter saw seems to accept ~2-1/16" or 2-1/8" hoses. ...Trying to get the dimensions correct.

When I made a rookie mistake by yanking the miter saw's lock trigger too aggressively in the wrong direction, I snapped it. ...That's why I created this upgraded, 3D-printed trigger - one that's significantly more robust than its predecessor.

... occasions... ...as I did, and can't find the replacement part online. This part fits the 10" single bevel compound miter saw. You will need to use the original screws that came with the tool. ... The next time you break it, just print out another one.

This is a hose coupler/adapter to fit the Ridgid Shop Vacuum hose to the Ridgid 7-1/4" Compound Miter Saw. This is super-easily modifiable in OpenSCAD to adjust Hole dimension to accommodate different Ridgid Tools as needed. ... OpenSCAD is a free CAD...

This is a hose coupler/adapter to fit the Ridgid Shop Vacuum hose to the Ridgid 7-1/4" Compound Miter Saw. This is super-easily modifiable in OpenSCAD to adjust Hole dimension to accommodate different Ridgid Tools as needed. ... OpenSCAD is a free...

Hose adapter to fit a 14 gallon Ridgid shop vacuum with a 2 1/16" (2.0685") hose to a Ryobi miter saw with a 1.65" extraction tube. It fits well but you can add a bit of thread tape if you want more sticking power. ... Included the model file so it...

description bosch appliance collection

These are the components we engineered and utilized when we upgraded our shop's dust collection system and relocated it to the basement. The setup consists of a 4-inch to 2.5-inch adapter for routing the system through walls, floors, or ceilings, as...

This miter guide has a permanently set 45 degree angle to make more accurate miter joints.

Miter

I have the Kobalt 12" Compound Miter Saw, that tilts both directions. This is the locking handle for the tilt part of the saw. This handle is right next to the handle that locks the miter plate. THIS handle lifts up. The other handle pushes down....

An adapter to go from a Ryobi 10'' miter saw exhaust port to a Rigid 2.5'' wet/dry vac hose. I got so fed up trying to figure out which adapters to print I made my own. Someone told me you should flip it over so the wide end faces down when printing...

This is a replacement part specifically designed for the safety mechanism of the KC-9160 miter saw. It's essential to note that this particular part does not include the switch itself; instead, it's just the arm component. An updated version of the...

A high-performance collaboration unfolds between the DEWALT Flexvolt Sliding Miter Saw DHS790AT2 and Autodesk Maya Version 2018. Bringing a sophisticated 3D model, texturing, and rendering prowess courtesy of V-Ray Version 3.6 for Maya 2018 to the...

Blade Guard replacement for an older Delta Miter Saw. v1 it could be another 0.75 cm wide it does rub on the metal permanent guard. Also the pivoting hole needs to be another 1.0 cm away from the circumference of the overall blade guard, it was just...

Brackets for Bosch Track Saw Guide Two part print to attach Bosch track saw rails on cabinets and other surfaces. This works well in a vertical orientation and on some kind of smooth surface. ...I used it for the short guide rail and I can highly...

This modification was made to include a 1 11/16 option to complement the Dust Port of the DeWalt Mitre Saw.

Zero clearance inset / throat plate for Craftsman miter saw (model 137.212290). Bought the saw used and the throat plate was cracked and falling apart. I taped up the remnants and modeled a new one since these are impossible to find. Print with...

Zero Clearance Insert for DeWalt 12" Compound Miter Saw, Model DW715. I attempted to re-create the original as much as possible. It is not a tight fit, but neither was the original. After installation, run the saw through the insert to create a...

dust collection adapter dewalt dw745 and triton router table to 70mm (outer diameter)

4" to 3" dust collection hose reducer. ...Model created in Fusion 360.

ceiling holder Bosch clamps (FSNKZW ) https://www.boschtools.com/us/en/boschtools-ocs/track-plunge-saw-attachments-fsnkzw-199025-p/ Category: Machine Tools