bosch miter saw dust collection adapter 3d models

A design I conceptualized for the Bosch Compound Miter Saw GCM12SD-120-Volt [https://www.amazon.com/gp/product/B004323NNC/]. Unfortunately, my efforts resulted in a dead end, but I believe it may still be useful to someone else. Initially, I had...

I've been placing a bucket under my Rigid table saw to catch the majority of dust that falls through the dust chute. Dust bucket be gone!This is a reducer from 4" (table saw) to 1.75" (shop vac). Both my tools are Ridgid brand. Adapter is press...

Adapts 2 1/4" shop vac hose to a Dewalt radial arm saw. ... Offset to clear the saw.

Adapts 2 1/4" shop vac hose to a Dewalt radial arm saw eliminating the sawdust bag. Its offset to allow the hose to clear the saw. ...I found it prints best with the small diameter down.

A versatile solution designed for improved dust collection performance on the Kobal 12-inch miter saw. Offered in two convenient variations: the compact and the extended length. High-quality images showcase the shorter version of this accessory. ... To...

But I've got my miter saw nestled inside a dust hood, and what I really want is to control how the angle of the dust shoots out of the existing port, especially when cutting from the bottom up. ...This way, it gets sucked right back into the hood...

Another versatile vacuum adapter comes into play, this time enabling a small Shopvac to seamlessly connect with a Harbor Freight 10" miter saw. To facilitate customization, I've uploaded the SolidWorks part file, allowing you to modify it as needed.

An adapter for the Bosch Glide Saw (GCM12SD) to a Rockler Dust Right 4" tool port This re-uses the red composite ring from the original dust collection bag that comes with the saw. Simply remove the ring and place it onto the printed adapter. I...

I designed an adapter that shrinks the opening of the sawdust exhaust to accommodate a vacuum hose. The adapter's inner diameter is 1.5 inches, while its outer diameter measures 1.73 inches. ...This modification allows me to attach a vacuum hose to my...

I also modified the click-in-flaps to be stronger and stick out a bit more, because the original design did not plug in firmly enough and came off by itself a few times.The part in the pictures has been printed with NO SUPPORT.Please read the details...

I would like to recommend my cheap cyclone dust extractor project: https://www.thingiverse.com/thing:3669095 - just in case you are still searching for something to stick the other end of that hose to. ... If those 60mm seem to be just a bit too much...

I would also like to recommend my cheap cyclone dust extractor project (https://www.thingiverse.com/thing:3669095) - just in case you are still searching for something to stick the other end of that hose to :-) If those 60mm seem to be just a bit...

this is uploaded from the raven https://www.theraven.us/index.php/2020/02/22/dewalt-miter-saw-dust-collection/

Hikoki C8FSHG miter saw adapter from 57mm to 40mm. Fits to sewer pipe. ... https://youtu.be/Sq9EtU0trx8

Printed in draft mode and works just fine.

A DIY enthusiast connects a 12-inch Dewalt miter saw to a compact 4-inch dust collection hose, upgrading their workshop's efficiency and reducing cleanup time.

For any other information, here is the sight I got the original file from. https://www.theraven.us/index.php/2020/02/22/dewalt-miter-saw-dust-collection/

Simple adapter between Makita LS0815F Slide Compound Miter Saw and Kärcher WD3/WD5. Might work with other Kärcher shop vacuums. ...Saw side is slightly tapered from 50mm to 49mm.

I designed this miter bar because the one included with the saw has too much play. The aluminium miter slot is 21mm (when new) but will wear down with use and it will wear more at the front than the back.  Instructions:Print the test piece...

Adapter to hook a 2.5" shop vac vacuum hose to a Ryobi TS1345 mitre saw. ... (The actual diameter for the hose insert is ~2.25".)

This hose adapter snaps onto the dust port of the back of a DeWalt DW713. The other end of the adapter hooks up to a standard shop vac hose.Print with the Shop Vac end down. ...This allows the snap features to print with horizontal layers so that they...

Dust collection for Kobalt 12 inch Miter saw. Uses 4 of the magnets listed below, but honestly friction fits into place perfectly fine without them. There are 2 2-1/2 inch ports, but 1 is honestly sufficient if you're just using a shopvac; if...

Dust collection for Kobalt 12 inch Miter saw. Uses 4 of the magnets listed below, but honestly friction fits into place perfectly fine without them. There are 2 2-1/2 inch ports, but 1 is honestly sufficient if you're just using a shopvac; if...

I made this to mount on my MS250 Delta Miter Saw to catch the saw dust coming off of the blade and redirect to the bag or vacuum. 2nd iteration and it fits and works very well. ...There must have been an original plastic piece on the saw but it was...

Swap out the dust boot on your Harbor Freight 12-inch miter saw with a new one - just replace it, no need to worry about the 10-inch model since you don't have that one. ...The laser on this saw will still work perfectly fine, by the way, and it's...

Dust Port Adapter for DW713 Chop Saw and 1.75" Rigid ShopVac Hose Attachment The adapter features a precisely angled design to maximize clearance between the saw's back and surrounding walls, ensuring smooth hose movement. ... Print Settings: * Printer...

The other dust collectors that I've found on ebay have narrow openings for the hose and don't collect as well or they use the lower two holes on the base which are not as secure. To fix that, I've opened up the end of the hose on the inside to be...

Took inspiration from a previous design for the Dewalt 708 miter Saw Dust Assembly https://www.thingiverse.com/thing:612670 but the outlet nozzle on that was too large so started from scratch. Modeled in Blender (my first decent project). ... Updated...

Took inspiration from a previous design for the Dewalt 708 miter Saw Dust Assembly https://www.thingiverse.com/thing:612670 but the outlet nozzle on that was too large so started from scratch. Modeled in Blender (my first decent project). ... Updated...

... this adapter to connect my Dewalt Vacuum's 1-7/8" hose male end to my Dewalt DW715's 1-5/8" male port. ...Standard universal adapters didn't fit correctly, so I designed this one with a precise 1-degree taper on both sides for a secure connection.