bosch miter saw dust collection adapter 3d models

This a replacement part for a Hitachi sliding miter saw model C 10FS. This may work on other Hitachi miter saws. The table inserts become damaged after much use and need replacement. The inserts are longer than the 3D printer bed, so they are...

This is a replacement handle for a Delta miter saw. It is designed to drop the bolt into the handle as it is being printed. ...You will need to pause the print at the correct layer to insert the bolt.</p> Category: Replacement Parts

Simple Miter Box and Hacksaw Blade Handle

Customized version of https://www.thingiverse.com/thing:3607431 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3607431

Printing out these instructions will ensure that you never experience the miter slipping again. To adjust the graduations, I set them to 2.5 degrees and marked the crucial 22.5 degree spot. You'll need a 10-24 X 3/4" screw (I believe it's actually...

My debut design from start to finish, tailored specifically for a Ryobi A18MS01 Miter Saw Stand - and potentially also suitable for Craftsman Miter Saw Stands. The foot was crafted with precision, printed flawlessly and fitted perfectly on the first...

One thing that really gets under my skin, though, is trying to insert the end of the miter into a hole that's precisely its own size. ...The design of this particular part, which has an open top, makes it a breeze to slide it in from above - so much...

This protective case securely stores your plastic Starrett Miter Saw Protractor, conveniently accommodating OEM paperwork that comes with it. The lid fits tightly, providing a snug seal. ...If your printer accuracy is already well-calibrated, I suggest...

Again and again it happens that the bag tips over when you do something else. It sucks! So I quickly created a small cap. It could still be expanded 0.2-0.4mm. Printed as always in TPU/TPE/'rubber'. ... Printing time 19 minutes.

This a replacement part for a Hitachi sliding miter saw model C 10FS. This may work on other Hitachi miter saws. The table inserts become damaged after much use and need replacement.</p> <p>The inserts are longer than the 3D printer bed, so they are...

So everything about my miter saw is perfect except for one thing.... the laser. I watch a few youtube channels and they too were of the same opinion. I searched high and low for a solution and decided to make something myself. This modification...

Should you wish to make a miter sled, it is difficult to find anything to make a runner for it. So, here is a 8" long plastic runner that fits snug and can be made to slide easily and attach to your sled. ...I used two on my sled and it works good...

I took measurements directly from my Dewalt DWS780 Miter's dust tube. Diameter was about 41.2mm but then there a lip in the middle. After tinkering, I came to 43mm inner diameter for that side and it friction fits nicely. Should work with a...

I printed mine at 100% infill. Then I used CA glue right before screwing it down. ...Once I screwed down the insert, I made the cut.

This is for the request for a chop saw. ...I know there is a good "solid" saw like this out there... ...SolidWorks had a demo dataset of one a few years back.

I crafted this prototype based on a flawed original concept. ...Fresh Rigid saws feature a distinct size fence, which necessitated the creation of a new model.

Very simple design just add a screw ( 3mm or 5/16 ) and a wing nut This is the Dremel Moto-Saw...

Miter inserts were all chewed up, so I designed new ones as close as I could to the original. Should be easily modifiable if you want to try 0 clearance insert. To connect the two pieces, I had played with the idea of a puzzlepiece-like...

... into my own hands and created one from scratch. The design turned out to be surprisingly simple - all it required was adding a 3mm or 5/16 screw and a wing nut. This is actually the Dremel Moto-Saw that I'm referring to: http://amzn.to/2tRLE8T

This is a jig for cutting tile edges at 45° if you do not have a tilting arbor tile saw.  This would be useful for inside our outside corners on wall tile trim, and probably other stuff as well.  The version in the picture is an old one, the fence...

 Note: some parts should be printed out of TPU:Bosch GCM12SD Miter Saw - This saw has a goofy dust port that I've never liked and haven't been able to reliably connect anything to.  I designed adapters to handle two scenarios: 1. connecting to a...

This is a replacement wheel for the Bosch table saw. The original had its center half-circle hole worn out. ...

This is a universal dust collector hood that should fit most chop saws or miter saws. ...It has adjustable feet to allow adjustment in height.

The two objects allow you to connect either a 50mm (DN50) or a threaded 40mm sawdust vacuum hose to the Bosch GCM8 SJL miter saw. The 50mm model goes over the adapter, and can also be used with off-the-shelf DN50 pipe tubing. The 40mm variant can be...

Dust Reducer Adapter for Ryobi RTS12 Table Saw - from 4" Dust Hose to 2.5" (64mm) dust port. Prints with no supports needed. If you print with 0.3 layer height and 0.6 wall width, you can get a solid part with 2 outer walls right up against 2...

Dust Reducer Adapter for Ryobi RTS12 Table Saw - from 4" Dust Hose to 2.5" (64mm) dust port. Prints with no supports needed. If you print with 0.3 layer height and 0.6 wall width, you can get a solid part with 2 outer walls right up against 2 inner...

The 50mm model goes over the adapter and can also be used with off-the-shelf DN50 pipe tubing whilst the 40mm variant can be used to screw the hose into the adapter.By looking at the two objects it should be clear which is which.If you want or need...