bosch miter saw dust collection 3d models

- Saw Connector Test Fit: This end goes onto the saw - it should slide on with just a little resistance and twist and lock securely onto the dust port's lugs. - Hose Adapter Test Fit: Fits over the 2.5" dust collection hose, which is sized to slide...

- Saw Connector Test Fit: is the end that goes on the saw -- it should slide on with just a little resistance and should twist and lock securely onto the dust port's lugs. Hose Adapter Test Fit: fits over the 2.5" dust collection hose. This is...

This sleek Dust Collection Hood encases the saw blade, meticulously collecting every scrap of sawdust. With a compact printer at my disposal, I broke down the design into manageable pieces and expertly dovetailed them together, eliminating the need...

This is an adapter for a bigger dust collection hose. ...~60mm or 2.3" hose

This attachment perfectly fits onto a Bosch sliding compound miter saw, allowing it to be easily connected to a standard 2.5-inch dust collection hose. ...I designed and printed this adapter with three strong perimeter layers, making it rock-solid and...

It replaces the miter saw's bag with a 4 inch dust collection hose.This uses the OEM dust collector assembly that comes with the Bosch GCM12SD miter saw. It just replaces the dust collection bag with a hose connection instead. ...I used 16 10x3mm...

My Bosch Compound Miter Saw truly excels, yet its dust collection system leaves room for improvement. The dust port falls short of reaching the material, resulting in reduced dust capture. To rectify this issue, I created an extender that attaches...

Bosch Axial Glide Miter Saw Dust Redirectamajigger for the [GCM12SD](https://amzn.to/3mCvmMG) and presumably the [CM10GD](https://amzn.to/32RPnHn) *(affiliate links)* As seen on my dust-travel analysis video here: https://youtu.be/iDQSWgTmGFo Lately...

I created this solution because I was dissatisfied with the original dust collection on my Milwaukee Miter Saw. My preference in the workshop is to connect my vacuum directly to it, resulting in significantly less cleanup afterward. However, the saw...

It was inspired by:https://www.thingiverse.com/thing:6144528this is uploaded from the ravenhttps://www.theraven.us/index.php/2020/02/22/dewalt-miter-saw-dust-collection/The dust shroud can be attached two screw on the fence or use double sided tape...

I'm modifying my Tool Shop Miter Saw to connect it directly to my dust collection system, using a Rigid Shop Vac as the host for the larger end of the adapter. I've customized the design based on http://www.thingiverse.com/thing:1246651.

This is an adapter to connect a DeWalt DSW780 Miter Saw to a VacMaster Wallmounted 5HP shop vac. ...The bushing sizes are 42mm x 54mm.

This is an adapter for a Metabo miter saw to adapt to a 2" PVC pipe fitting or a 2.5" hose.

Modify to fit 4-inch dust collection hose requirements.

I made this model for a past teacher of mine who had two of these saws and the second one was missing the outlet cover. I had to sketch around the outlet because there was no straight line to measure off of. I then imported the picture into...

This part gets rid of that right angle piece that comes with these Bosch Glide Miter Saws. It allows a 2.5 inch dust collection hose to be attached in line, greatly increasing dust collection efficiency. You will need to remove the right...

This is a replacement for the crummy vacuum attachment (which broke on my saw) that allows you to attach a 4" dust collection duct to your Bosch hinged compound miter saw. Be careful which direction you slice this, as it needs to be sturdiest at the...

I wanted to plug my Bosch dust extractor to my Dewalt DWS774 mitter saw, so I designed this adapter.

I wanted to plug my Bosch dust extractor to my Dewalt DWS774 miter saw so I designed this.On the first version the hole for the vacuum lock was a bit wide so I reduced it on the second version. I also reduced the nuts' ears and added footprints for...

I needed to connect my Bosch dust extractor to my Dewalt DWS774 miter saw, so I created this adapter.\r\n\r\nIn the initial design, the vacuum lock hole was slightly too large, so I refined it on the second version. Additionally, I minimized the...

Remix for a 2"1/2 dust collection hose Thanks for the original design!

Remix for a 2"1/2 dust collection hose Thanks for the original design!

To assemble the adapter, simply remove the red composite ring from the original dust collection bag that comes with your saw and attach it to the printed component. The dimensions of the adapter match exactly the Bosch part where it fits into the...

extraction for your miter saw on your large extraction tube

... smaller shop space. Tested on these specific models: Vacuum: https://www.lowes.com/pd/Shop-Vac-12-Gallon-6-HP-Portable-Wet-Dry-Shop-Vacuum/1001435286 Saw: https://www.lowes.com/pd/DEWALT-12-in-15-Amp-Dual-Bevel-Sliding-Compound-Miter-Saw/1000145735

This print will convert the oval dust port to fit over a 1" vacuum hose (1.25" OD on the hose). ...&nbsp;The model was designed using imperial units, so you may have to convert to inches, depending on the slicer you are using.</p><p>&nbsp;</p>

A vacuum adaptor for a Bosch Miter Saw Vacuum hose: 36mm Miter saw: 41.40mm

A design I conceptualized for the Bosch Compound Miter Saw GCM12SD-120-Volt [https://www.amazon.com/gp/product/B004323NNC/]. Unfortunately, my efforts resulted in a dead end, but I believe it may still be useful to someone else. Initially, I had...

This re-uses the red composite ring from the original dust collection bag that comes with the saw. Simply remove the ring and place it onto the printed adapter. The dimensions are identical to the Bosch component where it is inserted into the saw,...

A versatile solution designed for improved dust collection performance on the Kobal 12-inch miter saw. Offered in two convenient variations: the compact and the extended length. High-quality images showcase the shorter version of this accessory. ... To...