bosch 1617 dust port 3d models

Thanks to B_Rich for the original design that sparked this project. I sourced M4*20 and M4*16 pan head screws, but unfortunately, they wouldn't fit through the body of the original due to its thickness. ...To address this issue, I recessed the holes to...

This is a vacuum adapter for the Bosch 1617 fix based router. You'll want to use this exclusively if you are using a festool hose, as the attachment type is designed to solidly lock in a festool hose with the cleantec end (27/32 mm). If not, use the...

This is a Bosch Router dust port for 2.5" hose. I designed based on https://www.thingiverse.com/thing:4895005 as I liked the core design but my table did not allow for original port orientation. my design has port come straight down. ...Also added...

This dust collector port fits any vacuum port with a ~1.25" nozzle. The neck tapers to 1.25" about halfway down, creating a snug fit. The hose shown is from the car cleaning kit for Rigid shop vacs. I designed this adapter for compactness, so it's...

This dust collector port is for any vacuum port that has a ~1.25" nozzle on it. The neck is tapered to 1.25" about half way down, fits nice and snug. The hose pictured is the hose from the car cleaning kit for Rigid shop vacs. I wanted to make this...

This dust boot was designed to deflect the air generated by the router away from the work piece. The dust boot is comprised of 3 major parts: Top, Center and Brush Ring. The top and Center sections are held together with M6 x 35mm bolts. The ends of...

Attaches to Bosch 1617EVS fixed base router for vacuum removal of debris. ...Hooks up to Festool 35mm hose.

Dust boot for Bosch 1617 router with air diverter and magnetic dust ring. 4" and 3" vacuum hose adapters are included. This project was created in a hurry so the Fusion timeline is probably a mess. I never had time to go back and clean it up. If...

Dust boot for Bosch 1617 router with air diverter and magnetic dust ring. 4" and 3" vacuum hose adapters are included.</p> <p>This project was created in a hurry so the Fusion timeline is probably a mess. I never had time to go back and clean it up.

When the dust port on my Bosch MRP23EVS router gave out, I designed this as a cost-effective alternative to ordering a replacement directly from Bosch's spare parts supplier.\r\nThis design is simple to print and comes out to be approximately $3.50...

Connect your dust collector 2.5" hose to collect the dust at the source of your Bosch Router.

I required the foundation of the Bosch 1617 for a project that I'm currently undertaking. ...Not finding any other Bosch 1617 resources available, I created this model in case others might need it someday.

Dust collection adapter for connecting the Bosch 1617 plunge base to Festool 27mm hose.Requires (2) M4x25mm screws.

Dust collection adapter for connecting the Bosch 1617 plunge base to Festool 27mm hose. ... Requires: (2) M3x10mm screws (2) M3 hex nuts (2) M4x25mm screws 3 perimeters, no supports.

Dust collection adapter for connecting the Bosch 1617 plunge base to Festool 27mm hose.Requires:(2) M3x10mm screws(2) M3 hex nuts(2) M4x25mm screws&nbsp;3 perimeters, no supports.

I created this dust collector for my Bosch Router's 1617 fixed base. It fits a 1.25" hose connector to my dust collector and uses two M5 x 10 - 20 mm long screws/bolts to secure it to the router base. The other dust collectors that I've found on...

... involving a hot glue bond between the extender and the saw's dust port. Notably, this modification has yielded remarkable results: nearly all dust is now being caught by the dust port, as opposed to roughly half of it prior to the upgrade.

My solution to enable a single vacuum hose connection to both dust ports of my Bosch RA1171 router table. The adapter mounts over the existing dust port hole in the router table cabinet and is secured with six M6x40mm flat head (countersunk) screws...

A dust port adapter for Bosch CCS180B circular saw. The official accessory 2610953099 is not sold in my country, so I made my own. The adapter is printed in 3 parts and needs to be glued together. The mounting hole on the footplate is for M4...

Dust boot for Bosch 1617 router with air diverter and magnetic dust ring. 4" and 3" vacuum hose adapters are included.The air diverter (center section) can be omitted if not needed. In that case, use M6x16mm bolts instead of the M6x35mm listed...

It may work for other Bosch tools and should work with any standard shop vac connection also. I recommend using a resin printer rather than FDM printer as the layers on an FDM printer could weaken and break with all of the movement which a sander...

Remixed to fit 27mm festool hose Simplified the geometry for reduced supports

This is a custom mounting system designed specifically for integrating the Bosch 1617 router into a CNC machine setup.

My current setup uses a Bosch 1617 spindle that cools itself by pulling air through the top and out of the bottom. This tends to push dust outside of the shroud and into the air, making it hard to work with. I created this little mount to redirect...

This is a spindle mount for a Bosch 1617EVS for the X-Carve CNC. It may work for any other 89mm spindle/router. Its a two part print. The back plate will be the same. There are two fronts. One for a Jtech laser and one without. ... This is untested...

Dust port adapter for the Makita LB1200F bandsaw to convert to convert to the Bosch Click N Clean connection

Dust Port Attachment for Bosch POF 1200 Plunge Base Router 2 screw connection and dustcollection on 360°. fitt for ID=26mm vacume hose. ... 2021-02-11: add the fusion 360 file

I wanted to get rid of my multiple adapters to plug my Bosch Dust Extractor to my Ryobi Orbital Sander (R18OS), so I designed this.

Here is a part that allows me to plug my Bosch Dust Extractor to my Ryobi Orbital Sander (R18ROS).As it uses the lock features of the two tools, it avoids the hose from unplugging during the use of the sander, and more importantly it let me lay aside...

This part lets you plug your Bosch Dust Extractor directly into your Ryobi Orbital Sander (R18ROS). It uses the lock features of both tools to keep the hose securely connected while you're using the sander, eliminating the risk of it coming...