bong slide bowl 3d models

SUPPORT FOR BOWL AND HOOKAH TOBACCOS PRINTED ON PLA AND IMAGES GLUED WITH TRANSFER

A tiny stand to hold your bowl steady while filling it up. Crafted to print without supports, although a brim or raft might be desired due to its petite feet which become unstable until the first arches are complete. ... The white one shown in the...

Adapter for fitting the Dynavap into classic bong stems with conic bowls. ...Included a slit for placing an o-ring if needed, I used teflon tape to make a seal, but it works fine without one.Orientate the tip towards the printing bed + add build plate...

Support for 18.8mm bong tube.\nBowl 18.8mm support for bong.\nPrint Settings\nPrinter:\n Dagoma Discovery 200 printer settings.\n \n Rafts:\n Not needed.\n \n Supports:\n Yes, enabled.\n \n Infill:\n PLA material selected.

Full sized functional bong. Use glass bowl, 14mm. ...(Bowl Not Included, would melt)

This is the Bowl (14mm.) of the bong. All parts fit together, you can assemble your unique bong by printing out the parts you need. Dimensions of this part: 33mm./33mm./27mm. Dimensions of the complete bong (if one middle part):...

This is just a super simple square to hold a single 18mm bowl/slide for a bong or rig.

bong

Bong, just a bong, the best bong, use whit any 14mm bowl and enjoy :)) (escalar a 20 cm de altura)

I wanted a stand to hold all my different sizes of bowl/slides for my bongs and rigs. ... Top: 18mm Middle: 14mm Bottom: 10mm

another bong

Use a glass pipe for the bowl, or make a bowl with aluminum foil. I've also included a key chain bong - print it at 50% size. You can also print the normal bong at 50% - makes a cool pen/wacom stylus holder. ... Print Settings: 0.2mm layer height 2...

This is just a standard 12" 9mm slide bong to be printed in any non toxic material. Here's the stem/slide I designed: https://www.thingiverse.com/thing:6100395 You can also find them on ebay and all over the internet if you look around. FOUND:...

just...a bong

Bong for smoking. ... Water pipe

bong illustrated with cannabis and Synonyms 10 mm tub.

BONG or PIPA of water for smoking herbs, cannabis.

A Head-Shaking Bong for This Moment: https://amzn.to/3q7GKQy

Humans are using "Bong For Tobacco" with an air of indifference and a shrug.

A model of a glass bong, used for smoking that chronic.

This is a Bong Keychain!!. Lots of thanks to BuoyantBong. ... https://www.twitch.tv/buoyantbong buoyantbong.com

... piece often used for recreational purposes and has been the subject of both positive and negative connotations throughout history. The term "bong" can vary depending on regional slang, but it generally refers to a water pipe device used for smoking.

People are using bongs to smoke; people are smiling. You need a smaller pipe to fit into its hole. ...A metal pipe works best, and it should resemble the one shown in the second image.

14 mm bowl. uploaded assembled piece as well as the base and mouthpiece separate. ...Enjoy!

A smoker's favorite companion, a cool little water pipe, known to many as a bong, is used to inhale cannabis, commonly referred to as marijuana or pot. The term "420" originated from a code number used by police and other authorities to denote...

Included a slit for placing an o-ring if needed, I used teflon tape to make a seal, but it works fine without one.Orientate the tip towards the printing bed + add build plate adhesion, no supports necessary

Pinted 10% infill with PLA

This is the Bowl (14mm.) of the bong. All parts fit together, you can assemble your unique bong by printing out the parts you need. There is also an adapter for a 110 mm glass dowel. and 140 mm. Under the shaft diameter of 14.5 mm. Dimensions of...