body 3d models

The Gryphon is a mostly 3D printable, hobby-grade, Nerf semi-automatic flywheel blaster. Its main design features are as follows:Uses 130 to 180 sized 20.4mm , brushed DC motors.Semi-auto by rack and pinion with 1:3 gear multiplication. The trigger...

This is my design of a toy meant to teach children about the effects of an inclined plane on a rope/pulley system and the forces involved.  There are 4 3D printed parts in total and 7 externally sourced common hardware materials.  OpenSCAD Source...

No short circuits between the V G and/or S wires. Hardware I used these end-stops: https://aliexpress.com/item/32959048821.html I am not affiliated with AliExpress nor TwoTrees and there are LOADS of identical/rebranded switches out there. You will...

Average those two altitudes, to get your result (we rotate and average to cancel out any errors due to the ring not hanging perfectly straight).Avoid windy days if you can't move out of the wind, as the ring blowing around reduces accuracy...

or it will sag and make contact with y-front/back-plate !)4x P-112-MINI-y-carriage-bearing-strap.stl Print settings:3 Perimeters4 top/bottom layers0.2mm layer height40% infillMay require custom support(brushed support enforcer in prusaslicer works...

If you encounter any layer separation or odd layer squish patterns that were not there before, ensure that the anti-wobble is not allowing any movement in the Z axis direction and adjust accordingly to make sure the pins cannot move up or down. ...

... once you have confirmed it's done. You will see just bars on the display only.</p> <p>After that load what ever Firmware you like be it 1.1.9 or 2.0. This will give you a fully clean install, with no hang overs from past FW. Category: 3D Printers

GND should be handled in the ribbon connector. Print instructionsCategory: 3D Printer Accessories Summary I like that the Artillery printers come with an RGB LED on the hotend. It's a nice touch! But what if it could be... Brighter? And more...

I found printing 16 a time eventually one clip would pop off and ruin the batch, the ears add enough bed adhesion to keep any from popping off, and it makes taking the pieces off the bed easier. Comments greatly appreciated, let me know what you...

Considering PINDA V2 sensors aren't very expensive, I'll probably just order one of those! Print instructionsCategory: 3D Printer Parts Summary I've been enjoying using the stock inductive Z endstop as a bed probe on my Artillery Genius, but was...

[ ] 3D Print included stl files [ ] sunlu_fan_mount.stl -- Mounts 50mm blower fan and thermistor to rear of fan case. [ ] sunlu_gauge_ring.stl -- circular slip ring for mounting the hygrometer to the front of the case. [ ]...

Also this shape is very special because you can use two V Plate and invert one to create a sort of "wave" that visually connect two I plate that is place up and down.Double C Plate* : This isn't a stand alone plate, this mean this plate is useless on...

You have to look very carefully at the top side to see that it is 3D printed. That said, I think I prefer the look of the first version. It is more special with the black part laying on top of the white background.</li></ol><p>Note that the .stl...

:)All of the parts in this project are designed to be 3D-printable without supports, and they're modular, meaning you can choose how many "planter" modules to put together to build your tower.The planter modules come in two varieties: modules which...

A take on norwegiancreation's PID ball balancing seesaw using an Arduino.Video of this...

You can cut the circle that's sandwich between the two 3D printed pieces with good scissors. The holes for the crews and the tube are harder to make. Be careful, this mesh is sharp and you can get cut. I'M SERIOUS. I managed to make the screw holes...

The information-processing equipment, for its part, will convert hypotheses into testable models and then test the models against data (which the human operator may designate roughly and identify as relevant when the computer presents them for his...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

Team includes depreciated models such as the Medjay Pharaohguard Blitzer and the Iteru Deadshot Thrower. Not necessary for undead teams but enjoy! ...The Dynastic Destroyers are a proxy for Shambling Undead, Human, and Khemri Blood Bowl teams All...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

Check out the Raspberry Pi 3B+ here: https://www.raspberrypi.org/products/raspberry-pi-3-model-b-plus/ The controls are simple but there's enough buttons for most games. D pad for direction control and 4 front buttons provide your basic SNES type...

... > No. I planned to use sensorless homing and didn't need it, so I didn't add it. # Misc * [If you are wondering where the beautiful Hemera model in the pictures came from, here is a link ](https://grabcad.com/library/e3d-hermes-hemera-v6-volcano-1)

They aren't really required - they just provide some more protection. In addition to the printed parts, you will need the following: 1) 1/4-20 threaded rod, 3" length 2) 2 1/4-20 nuts 3) 2 M6-1.0 hex bolts 16mm length 4) 2 M6-1.0 hex bolts 30mm...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

Most parts do not need support and can be printed using the model orientation. BaseTopMotor and the Lid need “support on built plate only”. MotorMount needs to be rotated by 90 degree on the closed end (the one with the screw holes). In addition, it...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...