bobiverse series 3d models

If you haven't seen it, search for the AGC restoration series by Curious Marc on YouTube and start at Part 1. Seeing as there are a few DSKY models around I thought I'd tackle the AGC computer chassis itself. Until recently, measurements for it have...

The design is based on the 3d chess from the old series (TOS) of Star Trek:I made some adjustments to take advantage of 3D printing and I improved the design to my liking. The size is a bit smaller than the original one, since I wanted to print the...

Also on ebay)](https://stahlin.com/product/j-series-12-x-10-x-5-inches-j1210hpl-enclosure/) [Hot Glue...

So I just have two 12V fans in series to cool the motherboard. I've included my remake of the HBP in the build: http://www.thingiverse.com/thing:35059 this will help reduce the sag in your HBP and I changed the rear plate to look more...

Please see the front idler tensioners used in the Gold Series OpenFront printer. https://www.thingiverse.com/thing:5176411 <b>Gaping Maw back plates with standard Rat Rig belt tensioners</b> 1. Gaping Maw 4028 fan mount back plate with...

&nbsp; The model was developed using information from HistoricBridges.org and Google Maps in Fusion 360.For more information and photos of the bridge, follow this...

You can access that location here: https://drive.google.com/drive/folders/1JM2DOtHiTZ7oCXfj8pLv7C4HLuIHjD8R?usp=sharing This is the sixth expansion parts kit meant to complement my original Star Trek Constitution Class Parts Kit, providing parts and...

There are also 2 LED mounts which fit to the bottom bolts of the fan & Probe mounts, these were used for a pair of white 5mm LEDs which I plugged in to a spare cooling fan connector (with proper series resistor) for basic bed illumination. Cable...

Skidmore architects proposed a tower with large 55,000-square-foot (5,100 m2) floors in the lower part of the building, and gradually tapered areas of floorplates in a series of setbacks, which would give the Sears Tower its distinctive look. As...

Ultimately, I went with two 1.5v LR44 batteries, in series, pressed against wires that are just slightly recessed next to the positive and negative contacts. By seating them in opposite sides of the wand, the system gets tensioned when the two halves...

Whatever you do, don't sleep in hell!Say hello to the third instalment of my Minecraft lamp series; The Minecraft Nether Portal LED Lamp. This model is again roughly ~1/8th scale with room added for internal electronics and features a symmetrical...

Gate is connected to input with a 2M2 resistor in series. The SRV5-4 diode array protects it. The source is grounded, the drain gets a small (100mV) positive voltage. The internal diode does not open at this voltage, nor does the P-MOSFET conduct on...

Important: All led pieces must be connected in series, no parallel connections! Step 5, Connect the Leafs Connect all leafs together with the M4 bolts together. Leave a 4mm gap between all leaf connections. Afterwards connect the endpoint of the...

The EPL-24-1L-LED-D-V2 is equipped with Larson Electronics specially designed dimmable LED T-series bulbs which produces 1,750 lumens total.This single lamp explosion proof LED linear fixture is lighter in weight, has a slimmer profile, and produces...

Updating the top detail to more resemble the item in the series.Revision 2: Edited the nacelles to include ribs along the top sections. The Nacelle Middles files and the Nacelle Rear files were affected by this change.Revision 3: Added beacon...

Together they do produce 8.4V when fully charged connected in series. This is too much for NeoPixel and NodeMcu as both need 5V. You could use linear regulator, however they are not the most efficient ones and lose a lot of energy through heat. In...

A game about parenting - Also some Tarot sized cardsEarthquakeEpic Card GameExploding kittensFallingFirefly: The GameFor SaleForbidden DesertForbidden IslandFuseGang of FourGaribaldiGrimoire ShuffleGuillotineHero Card seriesHero: Immortal KingHigh...

The Starfury launch system is also added to the model and on full display as in hyperspace the Starfury protection layers hull wise would be unnecessary, which means, as you can see in the pictures, I took it upon myself to develop the storage,...

Asterix, a cartoon character in the French comic book series The Adventures of Asterix.The main protagonist and hero of the story is Asterix, who, because of his shrewdness, is usually entrusted with the most important affairs of his village. &nbsp;...

**Updated 9/23/2022: pants.stl reloaded with the flat side down**Speedy Gonzales, a cartoon character in the Looney Tunes and Merrie Melodies series of short films produced by Warner Bros.He is portrayed as "The Fastest Mouse in all Mexico" with his...

The power through the part should be adequate at 4A without heat sinking it. Parts used in this project: 25x10mm Dual Ball Bearing Brushless fan 2 each:...

The full build instructions can be found on Instructables as it's a rather complex build!Be sure to watch the whole build video series on YouTube to get the whole experience of creating BMOctoprint and to help if you get stuck anywhere along the way....

a lot), maybe make that video for a second series and also give back to this community, as I've already had just as much joy of Thingiverse as of the printer itself. Please feel free to print your ownMinnie Monoprice and play with her, but do NOT use...

Most of this should work equally well with most Creality printers. The objective was to end up with an Ender 5tool changing capability, providebetter tool cooling,minimize loss of Y-axis, support aBLTouch, work with thestandard Creality hotend as...

...Painful: - https://leeselectronic.com/en/product/28601-25mm-pin-20pcs-xh-series.html - https://leeselectronic.com/en/product/285960-connectors-jst-xhs-3pin-250mm-m-f.html Build Instructions for non-switch one: 1. Print the non-switch light bar case.

These models are for creating a prop Jezrien's honorblade from The Stormlight Archive series, written by Brandon Sanderson. Printing these parts requires an X/Y space of 200 x 200 mm, and a Z height of 220mm. Along with the STL files, this zip...

If you do use two batteries make sure they are wired in Parallel and not in Series to ensure you only have 3V. If you wire incorrectly you will probably fry your board. I had a couple of metal battery clips that I had removed from an old baby toy...

There is doubtless much more to be discovered about this fascinating series of puzzle.The Printable Puzzle ProjectThe Printable Puzzle Project aims to make available high-quality open-source models of many puzzle designs. All of our models are posted...

DAT has a 470Ω series resistor, and both DAT and CLK are bi-directionally level-shifted from 3.3V to 5V by TXS0102DCU, to meet recommended operating conditions for most strips. | Device | GPIO | Notes | |:--------:|:-------:|:----------------| |...

Gate is connected to input with a 2M2 resistor in series. The SRV5-4 diode array protects it. The source is grounded, the drain gets a small (100mV) positive voltage. The internal diode does not open at this voltage, nor does the P-MOSFET conduct on...