boat rail clamp 3d models

I created the MasterKey Rails since there were no free clamp-on options available on Thingiverse. The rails are now available in 3 sizes: 1", 3", and 4.25". You will need two clamps and one base to complete the setup. I designed the clamps...

These units offer users the versatility needed to adapt to different rail thicknesses with interchangeable screws or inserts, while preventing damage from over-tightening due to self-centering mechanisms built into most clamp types. ...By allowing...

All,designed a simple clamp for the curtain rail so you can hang your christmas lights in them.This is designed for a 19mm rail with a thin curtain on it. ...It snaps on rather easily. Might be necessary to adjust the scale to get a snug fit on the rail...

......The table saw fence uses a TBS20 Linear rail, two TBR20UU bearing blocks and this clamp. ... Parts needed: 4x M6 nuts 1x M6x70 bolt 2x 7x13mm springs 1x M6 clamping lever The distance between the mounting holes on the base is the same as the TBR20UU.

... of Mounts: Mounts with Only One Open Side for the End of the Rail Mounts for the Middle of the Rail The Drilling Holes Are 6mm in Diameter. ### Update May 7, 2020: Added 29mm Rail Clamps, Closed on One Side Added 6mm Washers in Extra Large Size

... I would recommend a screw length of 20mm and the use of 2 M4 flat washers. I included two rail clamp derivatives, one with a hex nut insert and one without. Use both parts combined to allow for the use of 2 rails simultaneously. ... Enjoy.

I misplaced my rail clamps for a massive crimson reticle scope of mine (50mm as shown in the example image).\r\n\r\nManufactured at 100% infill and fits together seamlessly.\r\n\r\n---------\r\n\r\nIf you appreciate this, consider treating me to a...

A simple clamp for 12mm rod or linear rails, identical to dimensions of the aluminum one found on AliExpress but utilizing a different clamping technique. There are two versions available: one with fixed mounting holes and one featuring slotted holes...

One of the factory clamp halves broke for my 2004 Forester's roof rails, so this is a replacement. I modified the design slightly from the original so that this piece can be used on either the right or left side of the car, rather than the...

I wanted the cat5 cable to be accessed near to / the same way as the [power supply for my DIN lab](https://www.thingiverse.com/thing:4703604) so I came up with this; a simple device that clamps to DIN rail and has _one_ keystone jack. Prints...

I modified Electronsmith's packout rail bar clips to allow me to attach two 2" bars instead of one, allowing for more utility with the Packout drawers and other larger toolboxes. One small issue I ran into during assembly of these was having to...

This is an innovative re-creation of the DIN rail clamp in OpenSCAD. ...The polygon was designed with precision using pencil and paper, it can be easily imported into another design as: ...

Paddle hanger on boat rail. Rail diameter 25mm. ... Parts required: - 2pcs of hanger

If u want to mount a rail with 29mm on a wall, this is what you may need. ...There are two types of mounts:Mounts with only one open side for the end of the railMounts for the middle of the railThe drilling holes are 6mm.

I'm just going to whip up a replacement shower curtain rail fixing real fast since my wife managed to trash the previous one.

A versatile adapter for securing a variety of gear onto 15mm camera rails. ...Designed specifically for attaching miscellaneous equipment to cameras.

Solid Core Wire Clip for 2020 Printer Rail For best results insert and twist 90 degrees into place with a pair of standard pliers.

The flexure on this cable clamp is really nice Modifications: - Extended the release arm to make it toolless - Slightly more space on the non-release side to make it easier to mount - Added zip tie slots parallel to the clamp - 6mm thickness -> 10mm

I designed a clamp specifically for my FLSUN I3, after realizing that the original one lacked sufficient securing ability. To resolve this issue, I added a clamping section to enhance its overall performance and stability. ...This modification was...

Can be used with https://www.printables.com/model/217223-v_slotted_rail_10x20_250mmPlease Like and Follow me for design improvements.For access to the 3D Printing Knowledgebase with troubleshooting and design education, join our monthly Ko-fi...

In the International Space Station, it is essential to have numerous cable ties or tie-wraps, such as hose ties, zap-straps, or Velcro straps, for securing clamps effectively.

The International Space Station (ISS) requires a Handrail Clamp Assembly (HCA) design, printable via its onboard 3D printer. ...Astronauts utilize the HCA to establish secure fastening points essential in zero-gravity conditions for routine tasks.

I merged the concept developed by AGRV with some adjustments, optimizing its size for smoother performance on the rail system. ...Additionally, I widened the walls to prevent the nut and bolt from breaking easily, incorporating a protective design that...

Can be used with: https://cults3d.com/en/3d-model/tool/v_slotted_rail_10x20_250mm Please Like and Follow me for design improvements. For access to the 3D Printing Knowledgebase with troubleshooting and design education, join our monthly Ko-fi...

Made for M5 screws Not tested yet Used this part as a base to cut the clamp. https://www.thingiverse.com/thing:3481080/comments Print in 100% infill Please link me if you use it. Bracket updated as second half is too thin and doesn't print...

I designed a custom bar clamp for my bottle cutter project, basing it on https://www.thingiverse.com/thing:9325. However, I noticed that the original design had about 2 mm of extra space in it. ...So, I created an updated version with a similar look but...

This is a remix of https://www.thingiverse.com/thing:3059042: Changes: * Extended its length threefold, enabling me to construct a bridge up to 130cm as shown in the accompanying images (Utilizing two of these rails:...

I created a revised version of Thingiverse's https://www.thingiverse.com/thing:9325, taking into account that the bar clamp had about 2 mm of extra space in it. I re-designed a new look-a-like by removing 1.5 mm of that unused room. This design...

I could not find rub rail end caps for my 2019 Bass Tracker Boat, so i did my best to copy the broken one.

Will fit a 1" / 25mm rail Will hold 3 rods Made to fit Terhi 400 but will work with other boats as well. File to edit in Freecad if you want to do that. I do not care! ...:)