bn 220 vs bn 880 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

Plug options include a 5-15 15 amp straight blade plug for use with 120V explosion proof outlets, a 5-20 20 amp straight blade plug for use with 120V explosion proof outlets, or a 6-20 20 amp straight blade plug for use with 220-240V explosion proof...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes wall_thickness = 1.6 shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 height = 15 mirror = Yes shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 height = 15 shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

2 - 6x appropriate resistors for your LEDs (use this calculator or 220 Ohm resistors if unsure). A small amount of thin wire (~26AWG) (ideally in two colors; positive and negative). Heat shrink. Liquid electrical tape (or standard electrical...

Please note that the code sets the print head to the rear corner of the print bed (Y changed to 220 for safety reasons). *Part 1: TESTING G-CODE MOVES* Filename: 'ejectmove.gcode' G28 ; home G90 ; Absolute positioning G0 X0 Y220 Z15 ; set...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes height = 15 shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes wall_thickness = 1.6 shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=401429 Instructions Using the following options: pattern_copies = 20 inner_diameter = 55 pattern_rotation = 180 height = 10 pattern_size = 10 pattern =...

(see the print settings). For the LED-s I used 220 ohm resistors between the RPI GPIO pins and the LEDs. For the Reset button, you need to connect it to the RUN pins, that are located on the board. You need to solder some connector pins on it if you...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 67 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...

Power use is 220-250ma depending on mode. 4 x 3400mAh batteries would give 56hrs runtime. The cheapest 1000mAh cells you can find would still give 16hrs. Two 3mm LEDs, different colors (red/blue are the stock colors) Three 3mm x 12-15ish mm...

The scale of this model made in proportion to it. 1/8 for FDM version and 1/16 for SLS/SLA version.FDM version dimensions:After being printed will stand - 220 mm tall, 94 mm wide, 99 mm deep;SLS/DLP/​SLA version dimensions:After being printed will...

Plug options include a 5-15 15 amp straight blade plug for use with 120V explosion proof outlets, a 5-20 20 amp straight blade plug for use with 120V explosion proof outlets, or a 6-20 20 amp straight blade plug for use with 220-240V explosion proof...

I used 3V power (two AAA batteries) and two 220 Ohm resistors. You may adjust the circuit to your power selection. Battery holder I improvised a battery holder from things I found home. This includes a prototyping board, metal contacts from an old...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: height = 15 shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes height = 30 shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=279864 Instructions Using the following options: trunk_length = 40 branch_diameter_cutoff = 1.6 tip_max_ratio = 70 root_min_ratio = 50 max_number_of_branches_from_each_branch = 3...

http://www.thingiverse.com/apps/customizer/run?thing_id=401429 Instructions Using the following options: pattern_clip = 95 pattern_copies = 30 pattern_rotation = 180 inner_diameter = 60 height = 10 pattern =...

The list of parts you will need is as follows:An Arduino-based microcontroller (Arduino Pro Micro in my case)A real-time clock module (DS3231 or similar)A TowerPro MG995 continuous rotation servo motorA standard LEDA standard light-dependent resistor...

for PLA+ (.3mf and .gcode are in 0.15mm with the .3mf being optimized for Prusa MK3s+ Printers that are well calibrated or factory calibrated)  Hot-End Temp: 220-225 for first layer smush and good adhesion if not using brim (not suggested since...

That would recover a bed Y-dimension back to 220. So, after all the print area will be 210x220mm... Parts to print: all parts at last 50% infill, Gyroid or Quarter Qubic, PLA or PETG except two parts close to HotEnd, for them ABS is the must all...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes shape =...

Soldering the threaded inserts Heat the soldering iron to about 220 °C. Take the base and pen holder. Insert the threaded inserts into the holes in the base. One by one, place the tip of the soldering iron on each insert, waiting until the filament...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 shape =...