bmg clone ender 3 3d models

I made my own holder for P.I.N.D.A (PINDA) inductive autoleveling probe sensor made by Prusa RESEARCH in Prague. ...Designed to be mounted on nean's BMG v6 direct drive mount. ... This is a remix from https://www.thingiverse.com/thing:398515

This is combination filament guide and runout sensor for use with a BMG Extruder. These are the 2 files that I used to create it. ...(Please print the wheel from filament guide below to use with my stl.) https://www.thingiverse.com/thing:4459380 ...

A wider and taller filament runout sensor mount for BMG dual gear style extruders! Requires m3x20 fastners, nuts and washers to mount the sensor. I also removed the upper lock washers from the Z rod lead screw fastners and used normal washers for...

Added 1mm to X direction of BLtouch mount. ... I have a BLT clone and the connector was hitting the wall making it tilted, this gives a little more clearance from the wall. ... offset with this mount: 0, 50.

This is for compatibility with licenses of both Ender 3 and Voron Afterburner. This design is fully based on the originals, but adding an extra hole for ABL support on X right. Requires a Nema17 motor 23mm. Endstop offset is (-15, -15). If...

I re-routed a cable that was snagging after my recent BMG installation, so I drew it out in Fusion360 to ensure the cable passes under the extruder. This modification allows me to print taller prints without any obstruction from the cable. ... For the...

I'm creating an upgraded CR10 mount for my BMG extruder, fixing the lead-screw nut issue once and for all. To ensure a secure hold, I've made the recesses for the nuts incredibly tight, requiring you to press them in with either a pair of pliers or...

I've attempted a BMG/Pancake build, but with a twist - it aims to minimize torque on the carriage by positioning the motor as close as possible to the x-axis, which is also the center of mass. This unique design ensures that it can be printed without...

I'm remixing the Bondtech BMG dual extruder design to utilize a widely available Chinese filament sensor from AliExpress, replacing the original CR-10 filament sensor that I don't have on hand. The resulting design should be compatible with most 3D...

I changed the following: - improved the upper part of the radiator cooling channel to make it more "bridge-friendly" - added bltouch mount and wire channel for it - shifted the part cooling fan forward and up to get better clearance with the heat...

Available at https://www.thingiverse.com/thing:4460970, this design integrates a BMG style extruder. By shifting the mount 7mm forward, it accommodates the offset in the new gantry adapter seamlessly. ...This innovative approach also grants the...

------------------ Adaptation of print head parts from Dmitry Sorkin for Ender 3 Neo for nuts. **WARNING**: not tested on V6, there is a good chance it is only suitable for Volcano. List of changes: 1. The part **mount** is adapted to the...

Esto es sólo una adaptación sencilla y rápida para ender 3 v2. El soporte original del bltouch está diseñado por Guilouz (ver comentarios en el post original), yo tan solo lo he reforzado un poco. Mi motor pancake no encajaba en la pieza original...

Esto es sólo una adaptación sencilla y rápida para ender 3 v2. El soporte original del bltouch está diseñado por Guilouz (ver comentarios en el post original), yo tan solo lo he reforzado un poco. Mi motor pancake no encajaba en la pieza original...

This is to mount a Bondtech BMG instead of the stock extruder and also added a BLtouch mount. I also added back the tab where wires exit to attach hotend wiring with wire tie as in original design of fan shroud. I have not mounted it yet. But I...

I remixed the bracket to include an 18mm proximity sensor on the right side, perfect for the Ender 3 upgrade. A 40 mm duct is now attached to the setup, which should work seamlessly together. I also extended the motor mount base to accommodate heavy...

convert your Ender to direvt drive with only one simple print and minimalistic modification to your existing setup 

- The extended filament pathway clashed with the standard BMG extruder. - Cooling was inadequate due to its distance from the nozzle. This design eliminates the wire passage through a hole, resulting in a slightly messier appearance but...

This is a remix of the Drivinator and one or two more, designed to work with the dual gear BMG style extruders, and I added a mount point for BL Touch style ABL probe (I used to have the 3D Touch probe installed until my BTT SKR Mini E3 V2.0 died and...

Still a work in progress, will try in my own ender first, but the prototypes seem to fit quite nicely. ...Will work further on tolerances, if you print it, feedback will be really apreciated!

My requirements were: + Use 2 4020 or 4010 fans + Direct drive with BMG - Stock hotend - No loss in build height and XY dimensions - Great access to heater block - Voron inspired ish :) - BLtouch mount - Cable chain I've uploaded a zip file that...

... ABL system. I needed it to work with the BMG Extruder in the direct drive setup, so I needed a custom mounting plate. Please watch TeachingTech's video for full instructions on installation and Marlin setup. ... https://youtu.be/hs6IVfNrf5k

I needed it to work with the BMG Extruder in the direct drive setup, so I needed a custom mounting plate. Please watch TeachingTech's video for full instructions on installation and Marlin setup. ... https://youtu.be/hs6IVfNrf5k Category: 3D Printer...

don't have one to try retains stock ender 40 x 10 hotend fan included Adapter with +1mm in length for shorter nozzles Changes include: Extruder can stay on while fixing clogs Fixed bl touch, so no re calibrating z offset, (bl touch offset 32, -2,...

al in one BL TOUCH OFFSETx_offset: -42.8y_offset: -15KLIPPER EXTRUDERmicrosteps: 16full_steps_per_rotation: 200gear_ratio: 3:1rotation_distance: 23.132

This is my clone of the great Bullseye fan duct for the Ender 3/CR-10, designed specifically for direct drive extruders which place the extruder stepper directly above the hotend parallel with the Y axis. If you've struggled to fit a Bullseye duct to...

For optimal results, use X +53 | Y -3 offsets but it's recommended to install and test these values personally. The Y offset is particularly important as the weight of the EZABL can cause flexing in some cases, resulting in readings anywhere from +6...

3 @16.1.2021 Cable holder added ####Rev. 2 @ 6.1.2021 Few small modification in the source files. BLTouch offset: -27,2mm in X; -31,4 mm in Y. Z axis is up to you (please follow manufacturer instruction). ####Rev. 1 Both body parts are screwed...

3 @16.1.2021 Cable holder added ####Rev. 2 @ 6.1.2021 Few small modification in the source files. BLTouch offset: -27,2mm in X; -31,4 mm in Y. Z axis is up to you (please follow manufacturer instruction). ####Rev. 1 Both body parts are screwed...

v1.3 was uploaded and the only tweak was removing a little material to the cable management on the left side so the stepper motor fit a little better. Overall, I think this is 'done'. It prints well in the orientation shown, it mounts solidly and...