blv mgn cube 3d models

I conceptualized a volcano-style hot end shroud, and while it's still in the design phase, I haven't had the chance to test print it yet - I'll be sure to update this post as soon as that happens. ... Additionally, I created an enhanced 10mm tall...

I just added extensions to the fins to make printing a breeze. ...Big thanks to @7effrey for the awesome volcano upgrade!

This is a revised design based on Ben's Twin Fan Hotend cover, tailored to be used with a closed system. ...The updated model features a secure lid that effectively seals in the internal components, while also incorporating a convenient cable chain...

This design features a protective shield to house two 4010 fans, along with a precision-cut slot for a 20mm thick tool fan. ...Every component is factory-standard, apart from the custom-cut opening.

I made a add on for the existing direct motor mount. ...Just adding a 2in1 part here if someone wants to just print one part.

this is my project for the modernization of the Z-axis drive using a belt drive (chain hoist) at the construction stage, I read a lot of forums where people on various printers suffered from crooked screws for driving the table, and I thought why...

I extended https://www.thingiverse.com/thing:3734786 to give more room for the power plugs, making them slide smoothly into the box without any forced bends.

UPDATE 23.08.2020 - I added 19 mm and 22 mm tolerance test STLs, so you can tune your printer/slicer before printing the parts. They print fast - 19mm is for corners, and 22 for lead screw bearings. When printing these PC-ABS or any hard...

It's a reworked version of HugoHuge's filament holder. The bracket is designed to fit snugly around a 2040 profile. The bracket can be secured on the rear left or rear right frame, depending on your preference. However, I've installed three...

This is simple remix from the original part, adopt for the metal kit. My fan, is fit tight in printed part without any screw. I use tinkercad. ...This model not nice, but works fine :)

I didn't find any cable support for direct drive so i designed these with hinges. For hinges i used M3 thread rod 55 and 60mm long with nuts on each side. The cables are then secured with zip ties. On the stepper it holds using zip tie. ...Also dont...

A basic enclosure designed to house a Meanwell RSP-500-24 power supply on a 2020 aluminum extrusion, created in 2020.

A simple remix to use the OG cable holder.

This setup includes cable chain mounts specifically engineered for the CR-10 bed, ensuring that the bed frame's mount extends far enough outward to position the pathway directly beneath the wires. ...The wall-mounted cable chain features a conduit that...

#Update 30/05/2019 V3 is probably the final iteration, taking a long time to complete. The LCD screen is now positioned in front of the surface at a comfortable angle of 35 degrees, allowing for clear visibility from almost anywhere. With this...

Checking on the original mount for Prusa 3D printers is a must when verifying the compatibility of a screw and nut with the Articulating Raspberry Pi Camera Mount, especially for users who own either the Prusa MK3 or MK2.

<p>This is a closed version of Ben's published Twin Fan Hotend cover.</p> <p>It has a lid and a holder for the cable chain.</p> Category: 3D Printer Accessories

The 5/8 inch tube was too small for all the wires required for the direct drive system. So, I added a second tube to accommodate the Hot End Heater and Thermal-couple. You'll need to print two xtruder tubes and one left clip along with one right...

Work in Progress, not tested! ...^^

For this remix, I extended the neck of the original knob by 5mm, for a little extra clearance below the frame, and made the hole large enough for an M4 threaded insert.

Work in Progress: X/Y Remix for 3030 Completed: - Right_corner Top - Right_corner Block - Right_corner Bottom_aux - X_mount Bottom_right - X_mount Top_right - Left_corner Top - Left_corner Block - Left_Tensioner mount - Right_Tensioner mount -...

<p>UPDATE: I'll do not recommend this design when printing over 60mm/s. Check out my other things for better cooling.</p> <p>Just extended the fins to the bottom for easyer print. ...Thank you @7effrey for the volcano modification!</p> Category: 3D...

https://www.thingiverse.com/thing:4332736 remix to fit metal kit

The creator of this impressive Titan model on Thingiverse has cleverly corrected a 3mm discrepancy, giving it newfound precision and accuracy.

Idler assembly consists of a sandwich of 10mm washer, shim, idler, shim, and 10mm washer stacked on top of each other. It's perfectly fine to utilize the carriage from https://www.thingiverse.com/thing:3642654 as a reference point for this design.

I have modified the Trianglelab Matrix adapter to fit the Hermera XS screw holes.

Long stem bed leveling thumbwheel holds M4 nut. 100% solid all the way to the bottom - that's the difference compared to https://www.thingiverse.com/thing:3715356, which sparked this remix. ... Edit and modify here:...

This is a custom LED mount designed specifically to illuminate the print head, featuring two strips angled at 45 degrees towards the bed for optimal lighting. The design incorporates convenient wire holders and three slots for secure ziptie...

I remixed the MachBar spool holder mount, which is itself a remix of HugoHuge's original design. Since I'm using 5mm extrusion rails, I swapped out the M3 screws for better compatibility. This version also eliminates the need for supports. ... The...

Diameter modified to accommodate 8 millimeter lead screws.