blue ice mic 3d models

This mic stand is specifically designed to work seamlessly with the Blue Ice Mic, offering a more tailored fit compared to the standard one that comes bundled with the microphone. As an individual who values precision and comfort, I created this...

This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. ... V4 sits a bit lower Fusion 360...

This is a replacement part for the Blue Snowball mic stand. Factory plastic parts on the legs are subjected to considerable pressure, making them prone to breaking. To create this part, simply print with an infill of about 35-40%. No supports are...

Remix of clypp's design (https://www.thingiverse.com/thing:4315674) Used for the Blue Snowball iCE microphone, particularly for the models where you can't screw off the stand. This revision makes it so the parts wrap around the stand. Previously, you...

Made this to keep my Blue Snowball microphone from sliding off the desk and causing chaos. Enjoy! ...Threads made possible by: https://www.thingiverse.com/thing:193647 Print Settings Printer Brand: Printrbot Printer: Simple Black Rafts: None Required...

Blue Snowball Mic

Solidworks 3D model of my Blue Yeti USB Mic

Solidworks 3D model of my Blue Yeti USB Mic

... ...The original STL was hollowed out for straightforward slicing and printing. Black is probably the best color to print it with but I think using any color that will stand out is better so you'll never forget to remove the cover before using the mic.

This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. V4 sits lower. ... Fusion 360 archive...

Blue Yeti Mic Stand Spacer Lost the spacer to my Blue Yeti microphone and designed this replacement spacer.

... part, as it contains M15.5x1.0 thread, which is pretty fine and could turn out not well enough). No supports required. This model is set remixed as the thread to the mic stand is taken from the 'Blue Snowball Mic Armature Mount' by Janbro. ...

... temporary supports on the desk attachment. When attaching the mic, use the little rubber washers between the mic itself and the printed part. ...The dimensions match the holder that the mic comes with so it fits together in exactly the same way.

I remixed a haxespot lamp to accommodate my blue snowball microphone, attaching it via a threading adapter borrowed from another user. I also created custom couplers to connect to the arm's end, ensuring a rock-solid setup. While the mic couplers are...

The initial plan outlines a fundamental casing for Firefly Ice Blue's core design. ...It features two screw inserts at the base, which can optionally support diverse attachments such as a spring clip or a watch body.

Stay refreshed this summer by indulging in a cold scoop of your favorite ice cream flavor.

its two layer bottel out side is shiny inside is blue

I got myself a Mic stand with shock mount from Amazon (https://www.amazon.de/gp/product/B01LW1X43U/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1), and although I could directly mount my Blue snowball ICE Microphone on it, I would lose the shock mount...

I wanted a smaller and shorter mic stand than all the ones out there, so after a couple of tries, I came up with this one. It's quite stable and the little curve holds up to the mic's weight very well. ...

Just a stand I threw together for my Blue Yeti mic. ... It assumes you are not using a 90 degree cable, if you are there are better options.

This works with the Blue Yeti USB mic that measures approx 70mm OD at the side mounting screws. [The exact mic I have came with an arm for edge-of-desk mounting.](https://www.amazon.com/gp/product/B078MHS3SC/) You'll need to print 2 of the spacers...

A few slight tweaks to ChriL's Blue Yeti VIVO Mount:Since ChriL's design was for the full sized Blue Yeti mic, I adapted the microphone arm mount to fit the smaller, Blue Yeti Nano.Tweaked some tolerances for the printable screw to make for an easier...

After carefully removing the trim piece from the dash (a relatively straightforward process), I drilled a hole in the center console to allow the mic to pass through. As a result, the wire is completely concealed once the trim piece is replaced. ...A...

A quick solution for keeping your Blue Yeti mic grill clean, dust-free, and protected from damage. Black or White PLA recommended depending on your model. (It also doubles as a cup if you want) Diameter is 69mm (I initially tried 67mm and didn't...

... are needed. I used some 3-4mm thick bungie. Note: The handled design is untested I used this adjustable mic arm but it should work for any similar mic arms If you'd like to support me please check out my filament wishlist here or Paypal here

I needed a compact pop filter for my Snowball mic and wasn't willing to shell out $20 for a few dollars' worth of plastic, so I decided to print two mesh holders, attach a thin piece of fabric or mesh between them before assembling the model itself.

... are needed. I used some 3-4mm thick bungie. Note: The handled design is untested I used this adjustable mic arm but it should work for any similar mic arms If you'd like to support me please check out my filament wishlist here or Paypal here

The Blue Snowball leg joint on the stand is not that strong. Designed in Fusion 360, simply print and screw in the new one. ... 30-40% infill with .2 layer height gives plenty of strength using PLA.

I needed a simple way to attach my pop filter directly to the Blue Yeti microphone. Specifically, I was looking for designs that fit perfectly with the Auray PFSS-55 Pop Filter with Gooseneck, which can be found at B&H Photo (link below). ... Auray...