bltouch v3 1 3d models

A three lane 180 turn, this is a rebuild of a 1 year old turn using all the things i've learned in the last year. It allows for smooth 180 racing across 3 lanes. ...Cars with poor clearance do just barely high center in the middle but they still perform...

ABS is recommended as some parts will be near the nozzle :) The holes for the BLTouch screws are hidden under 2 layers of filament for better printability. Use a small screwdriver or something else to pierce through the two layers. I used this...

ABS is recommended as some parts will be near the nozzle :)The holes for the BLTouch screws are hidden under 2 layers of filament for better printability. ...Use a small screwdriver or something else to pierce through the two layers.I used this cable...

This is a BLtouch Holder for the Biqu B2 2 filament in 1 out

... To remove sensorless homing, you need to also not wire it in UART mode - UBL auto-bed levelling using BLTouch v3.2 - Software Endstops option enabled on LCD for setting the Z-offset Buy me a coffee if this helped you! ...- Love from London xx

Klipper firmware that I currently use with the hemera setup + bltouch You can use either v1 duct and v1 duct mount or use v2 fanduct(print it rotated 45 degrees, with duct channels up) 5015 fam My cr10 v3 has everyting stock hardware side, besides...

Marlin 2.0.6.1 compiled to use BLTouch for z-axis (in the plate centre point) homing and ABL.

I needed to remix a Satsana to fit my Ender 5 with the direct drive adapter kit and a Creality Spider v3 installed. None of the previous shrouds fit my set up just right. ... I printed with minimal painted on supports as shown in the picture.

This is a modified version of @bkvines outstanding Adjustable BLTouch Support, specifically tailored to accommodate the mounting requirements of a Wanhao Duplicator i3 v2.1.

A plate for mounting a genuine Antclabs BLTouch v3.1 on an Eryone Thinker SE (2021 version). It may also work on the Thinker S V2 and ER-20 as well, if it has the same plastic hotend cage. ### ANOTHER BLTouch mount plate? Yes, I bought a brand new...

Is a mount for bltouch and nf sunrise 1.2 extruder in ender 5 with top linear guide mod. It is mobile, you can adjust the bltouch heigh for volcano o another block. ... For more stability use 3 insert m3 and 3 screw (2 for fix mount and one for fix...

This is a remix from https://www.thingiverse.com/thing:4759716 To add a more sturdy mount

Difference between original and remix is the removal of a small annoying bump on one of the sides that was affecting my OCD.

If you own an Ender 5 Plus and install the Printermods MDD 1.2 direct drive plate, you'll discover that the stock metal BLTouch mounting plate won't fit properly. None of the pre-printed BLTouch mounts match, so I chose to modify the metal one...

The length should be perfect for the bltouch 3.1 ,but if it's too long you can always file the bottom end a bit. The remover is to be used if you need to remove the bltouch from the mount. This way you don't damage the probing needle accidentally. If...

1 Layer Gap Fix: A gap in the model before the BLtouch mount was fixed. BLtouch Mount Upgraded: The mount is now positioned higher, allowing more room to adjust its height. Washers and/or nuts may be needed for the original BLtouch. Printable...

BLTouch 3.1 Bracket/Mount for Creality Cr10S-Pro Printed out of PLA, a material that won't melt at high temperatures, I completed this project in approximately 24 minutes at a speed of 60mm/s without any support structures and using low resolution...

The person is a human. They possess qualities that are unique to humanity, such as consciousness and emotions. ...This individual has the capacity to learn, grow, and experience life in its entirety.

Customized version of https://www.thingiverse.com/thing:4089728 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4089728

Customized version of https://www.thingiverse.com/thing:2853626 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2853626

... wires to facilitate smoother connections. In a subsequent update, version V2.1 was released with additional features: - Incorporating a specialized mount for the NF Cyclops 3-in-1 sensor, which significantly boosts rigidity and overall stability.

Check out my [BLTouch Spacers](https://www.thingiverse.com/thing:3578888) I like the [Mistral 2.1 cooling duct](https://www.thingiverse.com/thing:2121279) and rendered a few images with it. It can use any stock Anet A8 duct and fan. This is meant...

I use original parts but I think it will work with clones : - BondTech BMG extruder - BondTech NEMA17 Pancake Stepper 25mm (The Creality stepper is to big) - e3D V6 hotend - BLTouch v3.1 Needed extra stuff : To fix the base on the eplate : *2x M3...

[find: Nozzle_to_Probe_Offset] -> Depending on what BLTouch holder you are using, measure the distance between the nozzle and BLTouch probe and enter the correct number. 4. [find: Graphical LCDs] -> If you are not using REPRAP_DISCOUNT_FULL...

This is a custom z-probe bracket specifically designed for the Wanhao Duplicator i3 v2.1, with precision probe hole spacing tailored for the BLTouch probe.\r\n\r\nDeveloped for the i3 v2, this bracket fits snugly around its newer rounded bearings on...

My settings: X_PROBE_OFFSET_FROM_EXTRUDER 39 Y_PROBE_OFFSET_FROM_EXTRUDER -46 Z_PROBE_OFFSET_FROM_EXTRUDER -1.20 // This needs to be modified LEFT_PROBE_BED_POSITION 39 RIGHT_PROBE_BED_POSITION 195 FRONT_PROBE_BED_POSITION 5 BACK_PROBE_BED_POSITION...

apologize now for my English ;) Small installation guide for BLTouch I. hardware modification a. I have the Hemera adapter from here https://www.thingiverse.com/thing:4033595 You can also use other adapters. But then the offset values have to...

You can use the original screw to mount the BLTouch without the nut. ... Y Offset : -40 X Offset : 0 this is mix of two design https://www.thingiverse.com/thing:4973141 https://www.thingiverse.com/thing:4973141