bltouch v3 1 3d models

BLTouch V3.1 can be used to model a mount. ...I tried to be very accurate.

I designed a 2mm thin cover for my BLTouch v3.1. ... Not sure if it works for older versions, but if you want to use it, be sure to check the dimension.

BLTouch Smart V3.1 was carefully examined by me, using authentic data from the manufacturer's specifications. ...This exhaustive analysis may prove useful for designing a custom hot end or fan bracket.

Based on the official Antclabs drawing specifications, I've meticulously rebuilt this BLTouch. ...Personal measurements have been taken into account to ensure accuracy, although some nuances in the middle section's rounded edges were approximated,...

BLTouch v3.1 mount for Ender 3 V2 2x M2.5x10 mm (BLTouch) 2x M3x8 mm (Mount)

This is a BLTouch V3.1 Spacing Gauge for the Sovol3D SV-01 Printer Instructions: It is recommended that you measure your BLTouch mounted and installed without any added spacer. Then, using this Gauge or any method of your choice, measure the BLTouch...

I put a lot of effort in to making this look real. My unit failed so I took it apart and modeled it as closely as I could. This is the most accurate model around.I made the textures in Fusion for rendering. The LEDs light up when in the right...

Remixed E3D Mount / Bltouch V3.1 / Original Fan 24V SAPPHIRE PRO / PLUS Improved FanDuct arround the nozzle much easier mount for all components adding bltouch with offset of 27mm Using direct drive with PTFE tube about 96mm improved the belts...

Improved E3D Mount with Bltouch V3.1 and Original Fan 24V Sapphire Pro / Plus A New FanDuct Design Surrounds the Nozzle, Making it Much Easier to Mount All Components. Adding Bltouch with a 27mm Offset Improves Performance. Direct Drive with PTFE...

I required a BLTouch V3.1 mount and only found one that was on the right side of the printhead. So I created one with it on the left side. And since I used the Quick Release System from Proper Printing, I remixed the Base V4 module. I measured it to...

This is my Document, in PDF format, outlining the process for Upgrading an Ender-3 with a BLTouch v3.1. I have crafted this as a straightforward step-by-step guide that anyone can follow. Completion date: May 2020. ...Last updated: June 20, 2020

I wanted to boost air circulation by installing a 40mm fan and securing my BLTouch sensor (BLTouch V3.1). To accomplish this, I simply attached the holder for the BLTouch. ...The printer in question is a Monoprice Select Mini Pro version 3 with its...

This part is for the new version bltouch plate, it supports the bltouch v3.0/3.1.

Suporte Bltouch Two Trees BlueR V3. ... Probe: - X: 0,00 mm - Y: -42,5mm - Z: Ajuste fino

Simple tool to adjust BLtouch Body to heatbed spacing8.3mm heightPin goes in U groove and small dimple on oposite side is for a finger.Home your printer, Release the screw on BLTouch mount, slide this gauge under the BLTousch body, make it sit flush...

Add BL Touch Attachment for Satsana Ender 3 Fan Duct\r\nFor Enhanced Precision and Print Quality\r\n\r\nI modified the original design from https://www.thingiverse.com/thing:4373721 by Leesirc to fit perfectly with the BlTouch v3.1, eliminating...

If you are using MKS Base 1.5 or above please IGNORE THIS CHANGE: `//#define X_DRIVER_TYPE A4988` `//#define Y_DRIVER_TYPE A4988` `//#define Z_DRIVER_TYPE A4988` `//#define X2_DRIVER_TYPE A4988` `//#define Y2_DRIVER_TYPE A4988` `//#define...

remixed from the V2, I wanted something that blended more with the shroud beside it and hid the ugly connector, looked good, and also something that didn't have holes but still has the honeycomb design because I hate the light of the BLTouch. ...

......To adjust the height, use washers. Position it as far from the hotend radiator as possible. Four M3 screws are required for installation. BLTouch: https://amzn.to/2EHRcdj (This is an affiliate link.) Offsets: - X probe Offset -1 - Y probe Offset -24

This is a mount for the BLTOUCH and Lulzbot v3 dual extruder head. It mounts on without the need for any additional screws or bolts, just use the existing three screws on the front face of the v3 extruder. Once mounted the bltouch has an offset...

BLTouch mounting flange to add auto-leveling to the ZYLTech Gear V3 printer. Print with your favorite filament. You'll need to make a few tweaks to your printer config to enable the BLTouch feature. Do a web search for "Robin Nano configuration...

*No extra hardware is required* This cover blocks the majority of light produced by the BLTouch while the printer is running. INSTALLATION - Slide the cover vertically (Bottom to Top) onto the BLTouch. ...It should fit a little snug and the hole should...

Made a remix for v3 and used the bltouch mount from [this remix](https://www.thingiverse.com/thing:4446190) made by [Marcus Bucher](https://www.thingiverse.com/mcbucher/designs). Settings are the same as original. The model is edited in blender, I...

This is a mounting bracket designed specifically for the BLTouch sensor used in the GermanRepRap Protos V3 3D Printer. It should also function seamlessly on the Protos V2 model as well. I would be truly grateful if someone could test this design and...

This part is designed to be push fit around the orange neck of the sensor (The bit with "smart" written on it) and around a BLTouch V3.1 (Other models are likely compatible, as well as knock offs) There will be movement in the cover once installed...

Since the BLTouch V3 have a new recommended distance from the nozzle-tip/printbed of 9.4mm I designed a new height gauge/adjustment tool to help those of us getting the probe setup just right. Need to be printed in either 0.1mm, 0.2mm (recommended)...

Since the BLTouch V3 recommends a new distance from nozzle-tip to printbed of 9.4mm, I created a custom height gauge/adjustment tool to help users get their probe setup just right. This tool needs to be printed in either 0.1mm, 0.2mm (recommended),...

eSun PLA+ Filament: https://www.bastelgarage.ch/pla-filament-1-75mm-schwarz-1kg-esun Original Creality BL-Touch retrofit kit : https://www.bastelgarage.ch/cr-10-v2-bltouch-auto-bed-leveling-sensor For the do-it-yourself alternative you need the...

BLTouch 3D Sensor Mount mounts to the extruder stepper motor on the MkII.

The BLTouch V3.1 is both 3.3V and 5V compatible and works like a charm. ...You can use the cable found here:...