blower fan duct for 50mm fan 3d models

This is a custom-made Fan Duct for the 7530 Blower used in Prusa I3 clones (Anet, Alunar, Weasy, etc.). I couldn't find a suitable fan duct for my blower, so I designed this one myself. The 7530 fan is an absolute powerhouse, blowing air with...

I swapped out a 10mm fan for a 15 mm blower fan, requiring me to fabricate an exhaust duct utilizing 3mm fasteners, but the holes could be sealed with tape instead of screws. ...Since the blower is made of ABS, I'm printing my duct in ABS as well,...

This is a versatile mount for the Snap-Fit Blower Fan Duct. The duct and mount combo enables you to swiftly rework your fan setup without requiring the creation of an entirely new fan duct. The standard fan duct settings worked exceptionally well,...

Since there aren't any good small fans out there, I switched to a radial fan. Finally, my heat break is getting cooled enough. Please check your Y-ENDSTOP after mounting everything. This thing was designed with Tinkercad. ...Edit it online at...

Updated the design made [Tevo Tornado Round Fan Duct for 5015 Blower](https://www.thingiverse.com/thing:2842573) to fit on an Ender 3 Pro with a Silicon cap.

Not a perfect fit, but good enough. Thorped's fan duct: http://www.thingiverse.com/thing:1621937/ Fan plate source code from http://www.thingiverse.com/thing:735038 Please note that the adapter should be used only until you get a radial fan; the...

This remix brings the blower fan closer on each side allowing for a more compact setup. The adjustable screw slot used for attaching this bracket to the Klemco mount is recessed, and is designed to be used with an M3 cap-head screw. To print the fan...

Exterior hole female - 50,3mm - 50,5mm - 51mm It's designed for DN50 pipe.

The concept here draws inspiration from the 50mm Supportless, Directed Cooling Fan Duct for MendelMax & Prusa at http://www.thingiverse.com/thing:63123; it's a reimagined version of that design.

... of removing support material from the original, fully enclosed design. To further optimize the print, I also meticulously removed the prominent Cetus/Tiertime logo on the side, ensuring a flawless adhesion surface for your preferred sticker.

Support added for enhanced rigidity to the Dual Blower/Radial Fan Duct Mount, designed by supasorn for Tevo Tarantula. Constructed in two parts to facilitate easy installation without interfering with hot end wiring. ...A single tie-wrap secures the fan...

The device is designed for a 50mm fan, which will direct airflow towards the manufactured item.

Adapter is to fit a 4010 blower fan to the 5015 fan duct model (with BL touch bracket) for the Ender3 v2 by Jargogler. ...Temporary solution with the intent to upgrade to a 5015 blower at a later stage without having to reprint a new fan duct. Print...

This is a counterpart to https://www.thingiverse.com/thing:4064197, featuring a duct for a 6048 blower-style cooling fan mounted on the left side of the extruder carriage and pointing down, roughly in line with the heat blocks. It's designed to be...

This fan duct is nearly identical to the original Remix by Cover1987, a stepper driver fan duct designed for 50mm fans. The main difference lies in the reinforced area where the fan mounts, allowing users to attach it using simple wood screws. I...

This is a prototype cooling fan duct I built to sit on top of my Surface Pro 7 to test if it would impact gaming performance. Printed with cura on "Normal" settings. Inserted a USB Powered 7515 blower fan from Amazon into the edge. ...

The fan hole is sized to an 5015 blower fan.Print with brim to better adhension and for nicer holes.Min. perimeters 2Bottom solid min. 3Top solid min. 2Infill 10%Slower speed is recommended on small perimeters for better screw holes and make...

... with the E3D hot end and this precise effector model: https://www.thingiverse.com/thing:2736931. ... Note: The successful operation of this fan adapter requires a 45mm x 10.5mm blower fan, similar to the one available at 12 V Fan AB4512HX-GD0.

This is a custom fan duct for the 5015 blower on the Tevo Tornado, designed to minimize modifications to the printer itself. The only components that need replacement are the existing cooling fan and a few additional screws and nuts. The redesigned...

A straightforward fan duct design for mounting at the back of a Wanhao i3 Plus 3D printer, inspired by the Cobra Fan concept found on Thingiverse under reference number 1090433.

Remix of Thorgeir's https://www.thingiverse.com/thing:4662109 using a 5020 blower fan instead of 5015.

I wanted a bit better fan on my Di3, but i didn't have any 51x51x15mm blower fans at home. But i did have a 25mm thick one, so i made this holder and duct to improve my performance. Bridge test used: http://www.thingiverse.com/thing:12925/#made Print...

I wanted a more powerful fan on my Duplicator i3, but I didn't have any 51x51x15mm blower fans at home. However, I did have a 25mm thick one, so I designed this holder and duct to boost my performance. Bridge test used:...

I wanted a bit better fan on my Di3, but i didn't have any 51x51x15mm blower fans at home. But i did have a 25mm thick one, so i made this holder and duct to improve my performance. Bridge test used: http://www.thingiverse.com/thing:12925/#made Print...

... works seamlessly with it and should be paired with a 50mm fan. Included are two washers and one M3 screw; an optional addition is using it with a scaled-up version of this design: http://www.thingiverse.com/thing:70981 (1.25 ratio for the 50mm fan).

Here is the rewritten text: Check out this video tutorial on how to build a custom fan duct: https://youtu.be/DKya-TY0xYQ I decided to print two halves of the fan duct separately, which proved to be a brilliant idea since it eliminated the need for...

Hello, Here's my fan cooling system for a mosquito and a smart effector with a 5015 blower. The duct part is based on the 5015 fan duct from **RH_Dreambox**. He's made very cool flow simulations, the duct is a solid deisgn, I've barely modified this...

To prevent damage from overheating, I threaded an M3x18mm screw into the hot sink to keep the fan duct and hot ends safely separated. ... Note: Be cautious when testing this modification, as it may significantly improve cooling efficiency - you might...

# R4Z0R A novel design for a lightweight, easy to clip-on/remove fan shroud, with a blower fan for the part cooling part. It is specially designed to be printed without supports, but to also be significantly stabilized if supported for the cable-tie...

R4Z0R A novel design for a lightweight, easy to clip-on/remove fan shroud, with a blower fan for the part cooling part. It is specially designed to be printed without supports, but to also be significantly stabilized if supported for the cable-tie...