blitzwolf bw shp6 tasmota 3d models

Hardware: https://www.blitzwolf.com/2300W-EU-WIFI-Smart-Socket-p-300.html https://www.aliexpress.com/item/Everlasting-100Pcs-Bag-Spring-Test-Probe-Pogo-Pin-P75-E2-Dia-1-3mm-Length-16-5mm/32920805035.html Tutorials:...

given, nor at any referenced site.Version 3 is here!Improvements have been done on :Overall stability of the adapterThe gap for the push button on the top has been extended so it doesn't get squeezedA recess for the Pogo pins, allowing more...

I recently discovered the Blitzwolf SHP-6 with the Tasmota firmware as a perfect replacement for my old 433 MHz home automation system. Unfortunately, flashing the SHP-6 is quite tedious since it requires taking apart the entire unit and soldering...

Earlier this year I printed RobinSt's great design, but I encountered two problems with it: a superfluous space for a DC-DC converter that I didn't need and no room for a second switch to disconnect GND and GPIO0. I wanted to ask Robin for the...

<p>Earlier this year I printed the great design by RobinSt but I had two issues with it:</p> <ul> <li>Extra space for a DC-DC converter that I don't need</li> <li>No space for a second switch to disconnect GND and GPIO0</li> </ul> <p>I wanted to ask...

This Is A Soundtrack For The BlitzWolf BW-F4 Wireless Speaker System

Juste un support fait rapidement pour le projecteur BlitzWolf® BW-V5 j'ai créé deux modèles: -un à fixer au mur -et un à accrocher ou vous voulez grace aux crochets Just a quick support for the BlitzWolf® BW-V5 projector I created two models: -one to...

There's a great description about how to build and use the adapter on the original page: https://www.thingiverse.com/thing:3476167 Pogo pins: P100-E2 (dia:1.5 x 33.3mm) You can get them from the usual places (eBay, Aliexpress, Banggood, …)...

Настенный держатель Blitzwolf Smart IR Controller BW-RC1. Мне не нравится блеск печати черным пластиком, поэтому включил в cura опцию нечеткая оболочка с размером 0.2 мм. Wall Mount Blitzwolf Smart IR Controller BW-RC1. ... I don't like the gloss of...

This is a front mounted holder for the blitzwolf bw-is4 smart thermometer. its designed to be permanently mounted inside a drybox. the 2 pieces of the mount should be glued together once you put the thermometer in. ... the batteries of the thermometer...

A simple charging stand for the BlitzWolf BW-AH1 smartwatch. I printed mine with 20% infill and 0.2 layer height sitting on the flat side and it came out just fine. There are 2 zip tie slots on the right side and 1 next to the charger to help...

I recently acquired this nice Desktop Lamp from BlitzWolf that goes on the top of a monitor. It is very well built has a RBG backlight but came with a problem: the holder that makes the lamp stays on the top of the monitor is magnetic and too big for...

I lost my Charging Cable for my Bone-Conduct Headphones BW-BTS6. I did not found any store, to order a new one, so i decided to do it by my own.I used the spring contact 90286-AS from Precimation (Brand Name Preci-Dip). ...I did not found this at normal...

Suport wall remote control projector BlitzWolf BW-VP6

Support for the sound bar wall mount BlitzWolf BW-SDB1 60W 36 inches.

Skadis Mount for the BlitzWolf BW-RC1 Wifi Smart Controller Any improvements or suggestions are welcome. ... Enjoy.

I built this gadget specifically for my own use, using a flimsy chain to suspend it from the ceiling. I had numerous other ideas that were more expensive than the chain solution. It was frustrating to find the right screw to attach the 3D print to...

HI! ... Here is the stl to print a Wall mount for BlitzWolf BW-HDC2 Splitter HDMI. Enjoy! Douns [ You like my design? Put on a like (it feels good)! You can too thank me with the "Tip Designer" button! ...]

Since the BlitzWolf LED Lamp BW-LT8 comes with stickers that don't quite cut it, I had to design custom mounting parts so I could secure them with screws instead.\r\nYou'll need to print 4 of these mounts and position them so the sharp edges align...

<p>Držiak kamery pre Ikea Lack Box</p>

Suitable for the original cable with a diameter of 3mm. ...Print Settings Printer Brand: RepRap Printer: Geeetech I3 Pro B Rafts: Doesn't matter Supports: Doesn't matter Resolution: 0.1 mm Infill: 100%

The BlitzWolf works fine, but it doesn't clip onto clothes like the Sony. I wish the +/- buttons on this device didn't skip tracks with short taps because it's too easy to accidentally skip tracks instead of changing volume (or just skipping tracks...

After many days of searching without success I decided to go it alone and draw up my own Smartwatch stand/charging dock. This cheap but versatile watch, is great but accessories seem to be hard to come by. I hope this stand come charging dock...

<p>Just a quick model I made so I can attach my PIR sensor to the wall and be able to quickly remove it any time I need to charge it.</p> <p>If you are going to build this, be sure to place it in the correct position, it only works one way (the...

Just a quick model I made so I can attach my PIR sensor to the wall and be able to quickly remove it any time I need to charge it. If you are going to build this, be sure to place it in the correct position, it only works one way (the gravity is...

Replacement for the easy to brake part of otherwise quite decent desk lamp. CAUTION: this version does not include rotation limiter so you can fully rotate the lamp instead of just +/- 90 degrees. Therefore be careful to not rotate in the same...

Replacement for the easy to brake part of otherwise quite decent desk lamp. CAUTION: this version does not include rotation limiter so you can fully rotate the lamp instead of just +/- 90 degrees. Therefore be careful to not rotate in the same...

Original idea: https://www.thingiverse.com/thing:5137703/files Print Settings Supports: Yes Resolution: 0.2 / 0.3 Infill: 30 - 40% Filament brand: 3dfila Filament material: ABS / PETG

The docking station for Blitzwolf bw-fye7 wireless earbuds lets you charge your earbuds on the go, giving you a convenient place to dock and recharge when needed.

I designed a custom jig to program the new version of the BlitzWolf BW-SHP6, as no suitable one was available. I added Pogo pins and the project was completed. The resulting product can also be marketed under the brand name Gosund. ...When programming...