blink doorbell wedge mount 3d models

very simple wallmount for blink sync module V1

A Bird Feeder with integrated Blink outdoor camera

Voronoi Blink Fox of Hearthstone mastery is renowned.

remixed a webcam arm to hold the blink mini

Hold the blink sync module below the power plug

**Variants** I've included two configurations: Model #1 - Mounting slots suitable for #10 screw diameter (0.19") - CAT6 Cable pass-through WITHOUT connector (0.25") Model #2 - Round mounting holes suitable for #10 screw diameter (0.19") - CAT6 Cable...

A bracket for a blink camera. ...Camera can be held on with Zip ties (recommended), and if adhesion promoter is used, then double sided tape will stick better to the bracket (to help with mounting to desired surface). ... Print Speed: 50 m/s

A bracket for a blink camera. ...Camera can be held on with Zip ties (recommended), and if adhesion promoter is used, then double sided tape will stick better to the bracket (to help with mounting to desired surface). ... Print Speed: 50 m/s

The design includes three STL files: * Shade only * Shade with top mounting point * Shade with bottom mounting point The design criteria are as follows: * Maximise shade without obstructing the camera's view or motion sensor. * Allow wind to pass...

The user seeks to augment the existing 15-degree plate that accompanies a ring doorbell by incorporating an additional angular component, specifically wedges offering more substantial degrees of adjustment. ... 15-Degree Angle Wedge 20-Degree Angle...

Could not find a mounting plate that would work with my existing cutout to install a outdoor flood. Plenty of 4" vinyl siding options but nothing for the older 3". ... Have only printed it so far in PLA, but probably should be printed in another...

Customized version of https://www.thingiverse.com/thing:4920150 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4920150

Customized version of https://www.thingiverse.com/thing:4920150 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4920150

Customized version of https://www.thingiverse.com/thing:4920150 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4920150

Customized version of https://www.thingiverse.com/thing:4920150 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4920150

Customized version of https://www.thingiverse.com/thing:4920150 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4920150

Customized version of https://www.thingiverse.com/thing:4920150 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4920150

Customized version of https://www.thingiverse.com/thing:4920150 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4920150

Customized version of https://www.thingiverse.com/thing:4920150 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4920150

2.25" extension

This Enhanced Mounting set includes: - Replacement Doorbell Bracket - 45 deg wedge for doorways that are recessed into the building. - 20mm stand-off for flat surface mounting It was necessary to redesign the supplied Doorbell Bracket in order to...

This is a shelf for Amazon Blink Mini This shelf allows the Blink Mini to stand upright on a wall Use it and costumize it at will

A simple custom wall-mount for the Amazon Blink Doorbell. ... i have created 2 version of this blink doorbell Round doorbell blink 12.8*7.6*0.6 cm internal diameter 5.87 cm Square doorbell blink 12*12.8*0.7 cm

This is a versatile indoor stand designed specifically for Blink XT2 cameras. To assemble it, attach the wall mount to the stand using six 6-32x1/2" bolts. The stand allows for full flexibility of the camera's position while in use. For optimal...

I customized the *Blink XT2 Sync module holder by cobretti* using Fusion 360 to remove the American-style plug (which is standard in the UK) and add a chamfered hole for wall mounting. [*Blink XT2 Sync Module Bracket with or without...

Blink Sync Module 2 in both Black (B) and White (W).

Remix of another knob I liked by tumad. ...Added recessed Blink 182 logo. ...

Two bright LED lights pulsate rapidly, their rhythmic blink a mesmerizing spectacle.

This is a Blink camera mount for the newest (2021) and previous camera versions. I've included the Fusion 360 (.f3d) files with the STL files to use for other cameras or to adjust the camera mount position. I printed the ball joint and nut...