blind model

Depending on your printer tolerances, it may be more or less tight, but if everything lines up it should be no problem.Fasten the 3 screws at the "top" (in this orientation) once the spine is flush with the caseCHANGELOG2022-03-01 - Moved away from...

... one at a time by clicking Download each time. Or click Download once on the file spider__man.rar ### My some other things: Category: 2D Art

It's worth the trouble to get access to a laser cutter to get cut panels.  The duct is intended to print at a 45 degree angle - the part model is oriented as it is intended to be printed. The duct part DOES NOT NEED SUPPORT. Your slicer may...

If you want to use the hardware I intended this to use:Hinges Bolts- https://www.mcmaster.com/91292A018/ (you will need to thread inner most hinge)Hinge spacer- https://www.mcmaster.com/91755A311/ (you can see in the photos a little bit of white in...

- You can find a somewhat more detailed list of supplies in my Instructable at https://www.instructables.com/Kissing-the-Frog-V20-Back-Horn-Bluetooth-Speaker-F/ Basically any combination will do (as long as the driver is 3.3" or smaller so it fits...

... broken and no one is going to fix it. ...Download files one at a time by clicking Download each time. ### My some other things: Category: 2D Art

Dimensions: 510 m × 330 m × 241 m Model scale: 1:3x103 (15cm) 1:8x103 (7cm) References "Lawrence, K. and Benner, L., Radar shape models of asteroids compiled by Lawrence V1.0. urn:nasa:pds:gbo.ast.jpl.radar.shape_models::1.0. ...NASA Planetary Data...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

The stock globe has a vent on the top and there are vents in the model to aid the convection cooling. Is it *really* needed, especially with the converter gone? Dunno so the optional rain cap comes with the caveat of possibly shortening diode...

This should be the first unit from the power supply mob unit -> this contains just leds and has 2 holes in the bottom for an input line and output line end cap unit -> this contains just leds and has a single input line hole in the bottom The...

  I also modelled in clips for these PCBs to hold them in place whilst soldering up.I will share my order for my PCBs on jlcpcb so anyone can order once I figure out how :D Tools RequiredSharp knifeLong Nose Pliers Note that the 3mf...

The first one was a box, with an RFID reader, that provided clues on its LCD screen and had a secret compartment that opened with a specific secret code. The second device was this Bocca della Verità with RFID in the mouth (it was a secret) provides...

This is an enhanced print bed filament dryer based on Design Prototype Test's video on the topic seen here: https://youtu.be/H1DoJxY6v_U.  The air flow has to make a 90 degree turn at the top and bottom, so I used a velocity stack for the top...

Of course, the main one I use so far is Cura, and nevertheless I am increasingly discovering interesting and, most importantly, easily implemented printing methods. In this model, I combined the world-old technology for assembling rectangular...

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

I did not integrate this into the grill itself as you might want to swap the location of the pi to either side based on your preference.I appreciate any tips to support my work!Print SettingsPrinter Brand:CrealityPrinter:Ender 3...

The Raspberry Pi controller has a radio module attached to it for issuing commands, though I used the slightly different NRF24L01+PA+LNA model which offers better range. You could also use the same NRF24L01+ module as the puck uses, the wiring and...

 It is recommended to use MERV13 or higher for virus carrying particles. The fan is a Black & Decker 9in Mini Box Fan, Model BFB09W*.CostAt the time of writing this the total cost is the same for each of the 3 versions as the different...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

Please check the pictures to see what's in this kit.This set includes: - Requiem Demon Hunters (6+6)- Requiem Wulfhearts (4+4)- Captain Fenrir - The Silver Hunter- Captain Fenrir - Wulfheart Form- Trisha the Houndmaster (+2 Mastiffs)- The Old Wolf...

Please check the images to see what it is included in this kit.This set contains: - Dwarven Berserkers (6 + 6)- Behemot Riders (4 + 4 + 4)- Durnir – Berserker Lord- Tarum Bloodhammer- Thyra Blood Priestess of Duum (Dwarf Pinup)- Skutagaard War...

The design uses 12 '10mm x 3mm' (the magnets are actually closer to 9.95mm x 2.67mm).This is a spin-off from my earlier light-pull magnetic door catch: https://www.printables.com/model/209370-magnetic-low-profile-floating-head-quiet-door-catc , but...

However, they are split down the middle so they can fit through the holes with a firm hand, before springing back to the larger size. So thank you for the reviewer who made me take a closer look at at my model.I am always open to others ideas or...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 0 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 stencil_pattern_line_thickness = 30 printer_tolerance = 0.4...

A round-pole design makes the assembly easier to handle and transport compared to square-shaped models.A horizontal T-mount platform is provided at the top of the tower for mounting customer-provided equipment. The tripod features a rotatable head...

No special settings except for the optional color change.I suggest setting also the infill and supports angles to 35 degrees so it matches the angle of the parts.If you also want to print the letters on the cover you can use the MMU2 (or equivalent...

Comments and suggestions are also very welcome.Update 2020-10-19 Kermi radiator mount clips now availableQuite a few new MultiClip Objects in the collection (link above).Update 2018-09-21 Updated the alignment helperNew: MultiClip Glue!Update...

This is a model and instructions for how to build your own fiber optic light engine that is smart and can be controlled through google home. This version uses a smart LED light bulb as the source of light. It can use any smart light bulb that is...

License ------- The "Arduino Nano NeoPixel Ring Base" models (.stl) are licensed under the [CC BY](https://creativecommons.org/licenses/by/4.0/) license by [Code and Make](https://codeandmake.com/). The "Arduino Nano NeoPixel Ring Base" code...