blender remove doubles 3d models

5 - In general for all my models, when removing parts from the printer bed, it's a **VERY** good idea to place left/right parts into separate containers to help with the assembly process. Sometimes the difference between the left and right parts is...

If power is removed the total's are lost but any calibration you did of course is retain. You can calibrate through a CLI on the serial port. Look at code documentation for clarity. To get a warning of filament failure I added a simple quadrature...

After printing the pins, you have to remove the small support on each side. Infill: 15%-20%</p> <p>Small cog: You need 8 small cogs. Infill: 15%</p> <p>Main cog: You need 4 main cogs. Infill: For the first 10mm you can print it with 15%. For the rest...

As an alternative, we also offer the EXHL-TRN-LE3-IR-1227 for 120-240V AC applications.This remote inspection camera utilizes 120dB true Wide Dynamic Range, 3D Digital Noise Reduction and a true day/night IR-Cut Filter Removal to produce clear images...

As an alternative, we also offer the EXHL-TRN-LE3-IR-1227 for 120-240V AC applications.This remote inspection camera utilizes 120dB true Wide Dynamic Range, 3D Digital Noise Reduction and a true day/night IR-Cut Filter Removal to produce clear images...

You can use it as a spare or remove one clamp from the final print. It is important to use PETG for the clamps, as PLA is probably too stiff and/or brittle, although this has not been tested by me.</p> <h3>Printing</h3><p>Print five (5) clamps (or...

I also added some small zip tie slots on the inside edges of the prop guards. I was hoping I could get away with the zip tie slots, but they ended up being a weak point, and I finally broke the frame when I crashed into a brick wall. Version 2.0...

An ammeter connection port is built-in and can be accessed by removing the jumper and connecting the meter to those two pins.If a more complex IR output for a particular purpose is needed an Arduino can be connected through the ammeter port. Don't...

Get some masking tape/blue tape, and tape the two pieces together, possibly also to the PiDP-11 case. Then carefully take out the screws, remove the back cover and addjust a touch of super-glue on the top of each of the tabs. Ideally, try to clamp...

The Rev 1 duct worked OK and I think looked great, but I found it a pain to remove the shroud assembly to access the hot ends. I think the Rev 2 duct is ugly as sin (I really wanted to has easy view of the heater blocks) but it gets the job done...

It will stabilize the most upper part, so the section that is important for the press fit comes out correctly. Assembly:just remove the brim from the shaft and hook.Clean up the edges of the hook with some fine sanding paperTHIS IS IMORTANT: The hook...

Also please be careful when removig the sign from the print bed and definitely let the part cool down before removing it. Because the signs only have a base of 3 layers they can be damaged or bend prettey easy when warm. For indoor purposes PLA is...

Also please be careful when removig the sign from the print bed and definitely let the part cool down before removing it. Because the signs only have a base of 3 layers they can be damaged or bend prettey easy, when taking it down from the...

You have to remove the two roller bearings on the right side of the X gantry to install the bucket. You will need some 1/16" or 1.5mm silicone sheet. I had a bunch from another project, there are lots of ways to get some. I've even seen people...

I added one washer to the rocket before balancing so that I could remove a little weight if necessary in the future. The boat tail and coupler both feature launch lugs for a standard Estes launch rod. However, I'm uncertain about how well they will...

It is not needed, but it is easier to remove the lid. I also added a baffle to mine using a 22 cm diameter circle of 1/4" plywood and the 10 cm standoffs from above. This acts like a Thien baffle, but it is slightly simpler to cut out. It is...

2/12/2020 - Removed the two separate base pieces and uploaded a base that fits the y axis bearings better. 2/13/2020 - I got the printer fully assembled and it works great. I uploaded the sketchup files and a plate of the core parts if anyone is...

... Grille - 120mm, 6 vanes, 4 rings, ASUS logo - [https://www.thingiverse.com/thing:2033662](https://www.thingiverse.com/thing:2033662) Note that there are some duplicate entries in the list. If you want to remove them, I can help with that as well.

It is now aligned on the axis. Use APC has a nice video using their tool https://youtu.be/qF-iK_BElBM Remove the K40 lens. Insert the tool into the lens tube so that it shines the dot up into the third mirror and reflects it back towards the second...

They can easily be replaced if they get broken, which is the main reason I decided to use replaceable silicone strips instead of gluing some other rubber to the surface.This brings me to the best way to place/remove the knives on the bar, which is to...

Download this too: https://www.thingiverse.com/thing:3920466 LAST UPDATE: I've removed all the pieces you don't need for the final build, now there are only the pieces you should print (and the bottom section for duplication in metal, and the wire...

Only matters when tightening or removing the screws, but I use a small drop of super glue to keep them in place. Just be careful not to glue the screws in or gum up the nut threads. I posted pictures of the stock adapter bracket next to my model...

It works well but requires patience during the install as the whole X-carriage will need to be removed in order to fit it. NOTE: I did not have the time to pay attention to the length of each screw that I used. I recall using M3 for everything...

The lower part has to be printed with support, but this can also be removed without problems. I printed it in PAL with a resolution of 0.2mm. PS1 / 2 controller connector: I made two different versions of the lower part of the case:...

Also please be careful when removig the sign from the print bed and definetly let the part cool down before removing it. Because the signs only have a base of 3 layers they can be damaged or bend prettey easy, when taking it down from the...

Most of mine seemed to have a good balance between friction to hold it in place, and ease of removal. Drag a sharp tool (e.g. ...a mini screwdriver or blade) around under the lip of the slide-in space to ensure there are no tendrils left that will...

For those who's personal 3D-printers can't quite tackle the fine detail of this Mia portrait, this bead is also available through Shapeways: https://www.shapeways.com/product/edit/QBZ4N3LNX I was reading comments online in which discussion of the...

handy for manually leveling the bed **END EDIT** This is part of my attempt to remove the use of v-wheels from the Anycubic Mega Zero. For this mod you will need the following parts: **Needed Parts** - (1) 350mm MGN9H - 300mm should work as well...

Peel from one end to remove the cut portion out from the groove. Sometimes using a small screwdriver will help start the peeling and enable smooth one-piece peeling of the cut V-ribbon. Finally, using the utility knife, cut directly on the last line...

Over 400 lines later I realized just how big and complex it got.I have simplified and removed some things I previously added to reduce confusion, so now I hope this is all fairly straight forward, but at the same time as versatile as it needs to...