blender on ipad pro 3d models

I've designed a camera mount specifically for attaching a Logitech C270 camera to the FlashForge Creator Pro 2015 model, and it doesn't require any glue or screws for attachment to the printer. I'm currently using a raspberry pi 3 with AstroPrint...

Clamp holder for an ASIair Pro / plus on a Skywatcher EQ-5 Pro leg.No requirements fot this printSo the ASair is close to the Go-to device

Remixed from Sonicfury's original design for the 12-inch iPad Pro, I adapted the bracket to work seamlessly with the 10-inch iPad Pro. The 10-inch iPad fit snugly into the controller clamp on DJI controllers, prompting me to remix this bracket...

... ! EDIT: Photos are from Older Functional version of the Holder but Way too close to Build Plate for my Liking, so here is the new updated version that should be ON POINT close to Zero Z Probe Offset, plus I think it looks better so.. ...Enjoy !

I had the direct drive module installed "https://www.thingiverse.com/thing:4129248" and really did not feel like taking it all apart just to install this, so I made it snap on. Worked like a charm. ...Also reinforced the chimney (forget what it is...

Snap on camera mount for Creality (no fasteners required) Print Settings: 2 to 3 Walls 4 Top 4 Bottom 10 % infill I created this arm because I did not want to disassemble my web cams mounting hardware. ...

I love to kick back and put my feet up on the floor even when soaring through the skies, so I designed these awesome footrest extensions to take my in-flight relaxation to new heights.

I wanted a place to keep the footprint of the switch small and not take up a lot of vertical space I used double-sided tape on the front of the dock to hold it in place

-example printed using CookieCad Mermaid HOW TO APPLY -snip off where the hole ends towards the crystals -use snippers to bend the remaining in towards the crystals -clip on end of belt by pushing in

This little clip, clips over the original on the inside of the headset to keep the original clip from falling off. ... You attach it, not by placing it in one go over it, but from the side, clip it under one side, then the other and then slider it...

I recently printed a modified version of the filament spooler holder designed by ali55, which is available on Thingiverse under reference number 1319713. However, after installation, I encountered an issue where the filament spooler made contact with...

This is a reliable "light" setup for piloting a DJI Phantom 2, 3 or 4 with an iPad Pro 10.5 inch or 12.9 inch screen securely attached to the RC unit via this link: https://www.thingiverse.com/thing:2814574. ... These holders provide a fast...

Faster polling results in lower delay but also increases the load on the ESP and on the WiFi or network in general (on OctoPrint too). Security Warning: This sketch sends unencrypted GET requests with the OctoPrint API key in cleartext through your...

This revised design combines elements from one of my earlier concepts, optimized for seamless integration with EvanTheVan's innovative snap-on ND filter concept. While still accommodating top-mounted batteries in a sleek, Toilet-Tank inspired...

CAD file included (.f3d) can be opened with AutoCad Fusion 360 Adds a gradual 45° bend to the input feed Works with the P3Pro front cover both on and off Works with or without PTFE tubing stubs Adding PTFE tubing stubs will add extra grip to the...

**CAD file included (.f3d) can be opened with AutoCad Fusion 360** * Adds a gradual 45° bend to the input feed * Works with the P3Pro front cover both on and off * Works with or without PTFE tubing stubs * Adding PTFE tubing stubs will add extra...

This design swaps out the traditional threaded outer case for a sleeker slip-on top cover, incorporating a thoughtful groove and pin mechanism to secure the cover firmly in place. To open or close the cover, users simply need to rotate it until it...

I've modified my support for the GPS tracker model RF-V16 at http://www.thingiverse.com/thing:2069236 to attach directly on the Mavic battery. Personally, I use my original design, which allows you to leave it attached even when changing batteries.

... the magnets at my local LOWES. I added 1mm drain holes so it could be printed flat on a resin printer. The screw used is an M3 12mm long and just threaded into the print. ...I am including the step file aswell incase you want to make any changes.

... much quieter than its 60mm counterpart. I was also able to remove a fan that cooled the larger stepper motor. Additionally, the 40mm heatsink fan on my aero clone is quieter than both the OEM 40mm fan and a 30mm fan I used on my e3d v6 clone mount.

Filament Guide positions spool in dry box on right side to save space on printer's left side.\r\n\r\nDry Box sits on printer's right side, with Teflon tube running along printer's back.\r\n\r\nGrabbing filament between extruder and filament detector...

- Re-done screw holes, since the original had not done a good job (holes were Not straight and full of random holes on sides) - Edges toned to be near completely flat where the original was not. - Added internal structure to get rid of potential...

Credits: This design is essentially a remix from: https://www.thingiverse.com/thing:3057351 But it also has an element from: https://www.thingiverse.com/thing:4979273 I have added these two as remix sources, but fro some reason I do not see that...

This listing is for a Monster model with a key ring or pendent hoop it is a STL instant down lode file for printing on a 3D printer. This is made for filament printing but could be printed on a resin printer. we would love to see what you make...

the cover no longer fits on it, but I had to replace the left side of the input cam with something reinforced anyway, so that the cover no longer fits on it anyway! I also put in ptfe tubes that protrude about 30 mm so that the filament can be...

This is an add-on to http://www.thingiverse.com/thing:735350, engineered to secure split loom (1/2" or stock Flashforge) covered wiring in place. The original design's small filler piece was deliberately omitted for this iteration. To ensure a flush...

* For a new printed case and cover, you can modify the dimensions using Cura or Thinkercat based on your 12-volt adapter's electronic pack. Components: * On/Off Button: Drill a suitable hole in the PSU case according to the button's back side and...

It appears to be a step-by-step guide for installing an E3D V6 hotend on a MakerGear M2 printer. The guide covers various steps, from preparing the adapter base and circuit board to mounting the fan shroud, installing the fan, and finally testing the...

I wanted a place to keep the footprint of the switch small and not take up a lot of vertical space I used double-sided tape on the front of the dock to hold it in place Print Settings Printer Brand: Prusa Printer: i3 MK3Rafts: No Supports: ...

Therefore, I designed this simple single-sided bracket that bolts on. It's very sturdy even at 5% infill. To install, you simply unscrew the original plastic parts and replace them with this part using the same screws. Next, slide the filament tube...