blender diaper model

This is a servo hinge setup for use with MIPRESIDENT's Iron Man Mark III helmet (http://www.thingiverse.com/thing:260152). You can see my final build here: http://www.thingiverse.com/make:286759 And a video of it in use here:...

Winston sculpted reproduction of Schwarzenegger's face in several poses out of silicone, clay and plaster.[41] The sequences set in 2029 and the stop-motion scenes were developed by Fantasy II, a special effects company headed by Gene Warren...

Bear Exxa 1.0 is available here: https://www.thingiverse.com/thing:4362586 IMPORTANT: The Bear X axis will currently limit you to what alternative extruder/tool options you can mount without creating an adapter plate as it is different than previous...

You may need to adjust your printer, sand the chamber a little, or apply some force, as the parts were modeled to fit with ZERO clearance, to assure the best possible bond when using superglue. Just apply superglue to the syringe holder anywhere...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

 READ BEFORE PRINTING!This is a non-commercial print, this means you are not allowed to sell files or prints of this model.______________________________________________________________________________________What is this?This is my fifth...

There seem to be quite some error margin in production, if your model is a bit too big to fit, just sand off maybe .5 mm from the sides to make it fit.Completely(!) remove any filament remains inside the two enclosure parts.Fit servo into upper half...

The “NANO 1” model follows (support for matrix / hemera already published). in addition to the name and logo (grant it to me) they share the same "SUPPORT BASE" component as a fixed base, and with the quick release (only 2 screws) to adapt in the...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 347-480V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture. .Wiring: These LED light fixtures...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

head), I recommend staying in a 18-25 mm range for the thread length, to give yourself some margin.For my US friends using imperial, you can use #4 screws but you will need to adjust the nut parameter in the f3d file.Also, I think it doesn't leave...

This has taken several months to work out the kinks, but I think I have a good working model now. However, here are a few things to note: Prior to any assembling of any of the parts, I have found it is best to pre-thread all of the screw holes...

There are a few 3D print models on thingiverse that will also fit here. The RC4WD 1/8 warn is using a dual motor setup, However, I have tested with the 3D print winch and winch replacement motor (bought on amazon), and it also works perfectly. ...

You can hold them in place with either ¼" wooden dowels or printed plastic cylinders.Next, glue the battery and motor carriages to the drivetrain as indicated in the CAD model. Drop a M3 screw (or plastic pin) into the slots, and insert the battery...

They should snap into position once you're close enough.25.Finally top of the “Prusadusa and the sands of time” clock by glueing the Prusadusa model onto the central pin sticking out of the cone in the middle. This is now your seconds...

However, for the non-threaded parts of your models there is no need to waste time and energy printing that fine (and slow). In the example below the use of variable layer height saves about 9 hours of printing time (which equals about 1.4 kWh of...

...More importantly, Thingiverse hasn't run their customizer queue since Jul 10, 2020 so until they fix that issue, you will have to install and run OpenSCAD (free software) on your own computer to process the code to create your own customized models.

Copy to your USB and just print it like you would a normal model: qidi-xplus-imate-icarus-dial-bed-leveling-script.gcode Caution! The dial holder attachment should not be inserted during normal prints, it may hit the frame and break! Step Files ...

Copy to your USB and just print it like you would a normal model: qidi-xplus-imate-icarus-dial-bed-leveling-script.gcode All done. Enjoy! Just a few tips on settings. The Dragon hotend does not need as much retraction as stock Qidi. I find around...

... The single-blade model can be reversed in most slicer programs to cut from one side or the other of the 120 film, as described earlier, in "Preparing This Tool." The OpenSCAD source file therefore lacks any provision to make this adjustment. ...

Adjust the bed leveling screw closest to where it measures and by the time the script has looped three times the bed will be perfectly level.Copy to your USB and just print it like you would a normal model (print the correct...

I was unaware that the MMU2S required changes to the extruder and almost decided to hold off and just install the SPA by itself, but I started poking through the assembly manual for the MMU2S and realized there were changes that needed to be made to...

In short, it means that we will be using the Name Tag creator  to make the base (and thus be able to add text, image files, &c), and then create fitting covers and holders in this program. (A mixed approach is to also create the base with...

 When you slice the model for your printer, check a few crucial layers to make sure that the bolt holes and nut slots leave enough wall thickness everywhere.A note about the coordinate system:  The enclosure is modelled on it's left side,...

Adjust the bed leveling screw closest to where it measures and by the time the script has looped three times the bed will be perfectly level.Copy to your USB and just print it like you would a normal model (print the correct...

If there’s a flat-ish STL model that you like, you can load both this and that stl into Cura, scale and move them around as needed, and slice: Cura automatically joins models where they overlap. There’s also an insert plate that fits inside style0,...

If there is too little filament on the coil, it is pointless to print a large model. And it's a pity to throw away the leftovers, too. But you can print such a trinket as a gift or just for your own pleasure. P.S. When printing this model, not a...

Copy to your USB and just print it like you would a normal model: qidi-xmax-icarus-dial-bed-leveling-script.gcode All done. Enjoy! Just a few tips on settings. The Dragon hotend does not need as much retraction as stock Qidi. I find around...

--- # Assembly ## Key Switch The key switch is a two-terminal model (aka, it only has "on" and "off" modes for simplicity) intended for generic Chinese electric scooter ignition. It is intended for a through-hole of ~10mm. I made it 11mm to account...

The information-processing equipment, for its part, will convert hypotheses into testable models and then test the models against data (which the human operator may designate roughly and identify as relevant when the computer presents them for his...