blender 3d model from photo

Supasorn's original lead screw nut holders should be used, and I included the files now for convenience; they haven't been changed from the original. All parts use M4 screws & T-nuts, except the motor mount, which uses M3 screws/nuts. All could...

The holes for zip ties have these dimensions: 3x1,6 [mm] NOTE 1: Normally I tend to release the design in f3d, not this time, this thing has taken me so much time of design. NOTE 2: Is splashproof, water enters, the SWAT from Specialised is not...

Rework of the original X ends by gregsaun for the MK3 Bear 2.1 full upgrade with parallelism adjustment of the rods.This mod allows ~400µm of vertical adjustment of the bottom rod on either end (+/-200µm from the exact position).It's a common problem...

I used https://electronics-project-hub.com/send-data-to-thingspeak-using-esp8266/ for inspiration on how to do this but made sure to run ESP8266 on 3.3 volts from an external power supply to not burn up the WiFi board. I'm including my adjustments...

Thank you! Looking forward to hearing from you! Best regards, [Your Name] Customer Support Representative XYZ Text Spinning Services www.xyztextspinningservices.com Phone: XXX-XXX-XXXX Email: support@xyztextspinningservices.com Office Hours: Monday...

... screw (M3X20) with locking nut. Be very careful not to cut ESCs cables while you thread the bolt. Push a thin rod to clear the way from the cables before threading the bolt. ... Now do this 3 more times (if you are flying a quad) and you are golden.

Suction turbine for Nilfisk Handy vacuum cleanerTo disassemble the vacuum cleaner, after removing the different screws you will need to force a little using a flat screwdriver wide enough to remove the black rubberized part which is clipped into the...

The flexible hose should be suspended overhead, centered on the work area and should have at least a 4 foot rise with ample slack so as not to place side loads on the tool anywhere within the work area. File Dust-Shoe-Mount.stl may be printed or cut...

This is used to locate the cable support that comes from the XY carriage. The Y-front OpenSCAD file gives an option whether or not to generate a support tube as part of the compilation (hopefully clear in the SCAD file). Common definitions file Note...

These gauges are available from many other retailers as well. [Digital Car Wheel Tire Gauge Meter, about...

Customize your own thing from Thingiverse using Customizer! Get a unique version of [http://www.thingiverse.com/thing:287025](http://www.thingiverse.com/thing:287025) with these options: panel_shape = 0, pixel\_size = 0.7, thickness = 0.5, grid\_size...

You suddenly realize the wireless charging isn't doing it for you, and you MUST arrive at your target destination at 100% battery then just pull out the USB cable from its cozy little nook and plug it in. -- IS IT WATERPROOF?? -- No its not,...

Change Log (now from oldest to newest): 2021-09-20: I fixed a minor issue with the exhaust file. 2021-09-23: I’ve added another faction’s head and matching shoulders, as well as a “body” piece that’s specific to them. I’ve also added another ranged...

The jig is required because from past experience issues happen if the tube ends are snapped individually instead of all at once. Things can get difficult, and the end result tends to be janky. The transparency film can pick up fingerprints...

This shroud is designed to be printed from the bottom up with minimal support across the blower entry, left fixtures, and right attachment sites. The nozzles print fine without support for the 4-nozzle version but require support for the...

I also removed text from the back panels as they didn't print right.\r\n\r\n- - - \r\n\r\nUpdate: 5/20/2019\r\n\r\nI added narrow side plates, made the parts of MKS and RPi 4-4 that mount to the front of the frame thinner, and adjusted alignment some...

The Ark Survival Evolved logo. Hollowed for leds and wires. Stand allow space for 9v battery, I use 9v battery holder with button on/off from aliexpress. ...(<a...

The fork light barriers for the encoder disks of the motors from level 0 are located under the battery. Depending on the fork light barrier used, you need a few distances to lift them to the correct height. There are also up to 44 5mm LEDs here. :)...

I mounted it on the right-hand side panel because it's easy to route the cable from there (the printrboard is at the bottom of this panel). I usually have it on a table, so the 45-degree angle gives me a good view of the LCD. I briefly considered...

on a modified Anet A8: https://youtu.be/r3VDSf2LWgQ Longer Video from the ABS print with small tips: https://youtu.be/Eq14PsOnR8U Inspired by the legendary "Makers Muse" Torture Egg: https://www.youtube.com/watch?v=_IHmfQviSoE More will come if you...

Do not change the magnification factors...Glue the two pieces together.Print the inscriptions in the chosen colors with the surface of the letters in contact with the printing plate, then detach each letter from its support strip, and glue the pieces...

This can be done with: PrusaSlicer using color change Cura using: Extensions &gt; Post processing &gt; Modify G-code &gt; Add a script &gt; filament change Prusa's ColorPrint webapp ("G-code is supported from Slic3r, Cura, KISSlicer and...

To allow a quick change of the spools, I use the Quick Release from https://www.thingiverse.com/thing:969358. I also found the placement of the extruder awkward, especially with the planned relocation of the filament. In addition, I am of the...

I would like to see someone do a full button up shirt and maybe even have the gears mesh from one shirt hole to the next!A good remix would be a stem off of the outer gear for a lavalier (lapel) microphone. This would be cool for a science or...

If you're only interested in printing a heart without the arrow or holes, I recommend checking out the remixed version from Emmett's original design at http://www.thingiverse.com/thing:670944. When it comes to printing, note that no rafts are...

The player whose connection of choice appears more times on the perimeter wins.&nbsp;Multiple Players (no board)Players take turns drawing a tile from the heap and placing it next to an already placed tile, ensuring connections between adjacent edges...

I made the following changes from the original: Increased the width of the landing feet below the motor. Mine are always getting banged up when landing on concrete and rocks. Added a cut through the center of the motor mounting surface so the arm...

The back also has a 75x75 VESA mounting pattern on it so you can mount it using that as well.Conventions used:All holes that need a Metal Insert are 4.4mm (and 6mm for the VESA) in diameter and are not counter-sunk.&nbsp;All holes that are pass...

35,000 Lumen output from only 300 wattsSuperior LED Benefits1. 60,000 hour lifespan.2. Can SAVE 50% or more on energy.3. Qualifies retrofit projects for financial incentives, including utility rebates, tax credits and energy loan programs.4. Reduces...

Grip can't lock in the fold position.The part that holds the grip needs to be sanded or cut back to accommodate the grip.The standard 17 size mag can lock in but the 19 size mag can't and will make it push out from the folded position. Slide not...