blade 230s v2 3d models
141134 3d models found related to blade 230s v2.cults3d
I designed the landing gear for the Blade 230s V2. It is a perfect fit. I printed these gear in about 4 hours. My gear is printed from ABS but other material will work. There are 3 files. They include a Landing Gear mount bracket legs that will...
thingiverse
I designed a windscreen wiper specifically for the Blade 230s RC helicopter, which fits perfectly onto the www.heli-scale-quality.com body intended for that model. To see the Blade 230s in action, you can check out pictures and a detailed description...
thingiverse
The new landing gear system is specifically designed to meet the requirements of the popular Blade 230s helicopter. This advanced system features a sturdy aluminum frame and durable plastic components that can withstand harsh weather conditions and...
thingiverse
This landing gear for the Blade 230s helicopter is angled at 2 degrees to make the tail sit about an inch higher than the stock landing gear. You'll need to print 2 "Brackets" and 2 "Skids". Print the brackets on their sides and use supports...
thingiverse
This is a replacement frame kit for the Blade 230S. You can still use the original electronics. 4 M2x10mm hex bolts and nuts are needed for clamping the tail boom. The nuts must be inserted\pressed in the right frame side. I printed all frame...
thingiverse
Replacement Skids for 230S Helicopter and Other Models Print Settings: Printer: XYZ Davinci Rafts: No Supports: No Resolution: Fine or Excellent Infill: 35 to 50% Notes: The finer the print, the better they will be. To achieve a smooth side, flip the...
thingiverse
Blade replacement skids arrive, boasting a remarkable 1g weight reduction and impressive strength, perhaps even surpassing their predecessors. Their sleeker design is undeniably captivating. These new skids expand by approximately 15mm in width and...
thingiverse
I recently acquired a carbon fiber landing skid plate for my Blade 230s. I purchased a set of aluminum and carbon fiber skids from Lynx, along with a replacement set of plates. Feeling uninspired today, I decided to create a block to store the spare...
thingiverse
This print is for the Blade 230s Helicopter but may work for others with the same type grommet and post canopy connectors. No modifications are required to the helicopter. Just remove the two rubber grommets from canopy and put them in the 3D...
thingiverse
This is a streamlined and lightweight replacement landing gear for the Blade 230S. Despite its appearance, the goal is to create something fast to print and disposable. It can be used as a direct replacement for the original landing gear or in...
thingiverse
This is a comprehensive tool for high-level operations on the Blade 230 S helicopter and potentially other models. Print Settings Resolution: Fine quality is achieved through precise settings. Infill: A 50% infill density provides a robust yet...
thingiverse
Blade holder designed specifically for the 230 series, requiring a fine-tuning process through sanding to ensure a precise fit with PLA materials. ...In contrast, the TPU semi-flex variant requires minimal to no sanding adjustments.
thingiverse
Blade 230s helicopter main rotor head linkage pair
thingiverse
Landing gear for Blade 230S V1 or V2 - I took the plunge, crashed, and designed these from scratch. Secure those skids to the gear with some CA glue. Printing without supports on an Ender 3 yields a noticeable bridging effect. ...To achieve a cleaner...
cults3d
Landing gear for Blade 230S V1 or V2. I crashed and designed these. Use some CA to glue the skids to the gear. I printed with no support and you can see the bridging effect on an Ender 3. ... Use support if you want to clean that up :)
thingiverse
Here's a part for the Blade 230s Helicopter. This is a pitch link for the swashplate to rotor head blade grip. If the link is too tight or too loose on the balls try scaling the print down or up a few fractions using whatever slicer you prefer.
thingiverse
I'm replacing the Blade 230s tail motor mount and fin as one single unit, utilizing a plastic replica of the lightweight microheli design. This modified setup tips the scales at approximately 1.2 grams lighter than its microheli counterpart and...
thingiverse
Replacement vertical tail fin for the Blade 230s, upgraded with carbon fiber/ABS materials that deliver stronger, cheaper, and lighter performance. Enlarging holes to 5/64 will ensure a secure fit. Future releases will include this modification as...
thingiverse
There are plenty of Scale kits available for the Blade 230s, which can be quite pricey but also incredibly detailed. On the other hand, simpler kits that won't break the bank are also an option. This is where 3D printing comes in - most parts can...
thingiverse
This is a precision blade 230s tail boom slotting jig. Position one piece of the jig on each end of the tail boom after cutting the boom to length. Then, snap the jig down firmly onto the workbench to align the holes for the slots. K&S #9807...
thingiverse
Designed to fit into kingdallen's Canopy Quick Connect: https://www.thingiverse.com/thing:4617671
thingiverse
Humans created a sleek vertical fin design for the 230 series that captures attention. ...When manufactured with a thickness of 0.6 units at both the top and bottom, it surprisingly weighs less than the original equipment model.
thingiverse
This set of frame supports features a 1.5mm flange all around and fits snugly into a 1.6mm hole, providing full support to the entire frame. ...The heli's tail heaviness makes it easy to add weight exactly where it's needed, and they simply pop in with...
grabcad
I sure do hope that this rewritten text meets with your approval! ...Please let me know if there's anything else I can spin for you.
thingiverse
I broke my second boom on my E-Flite 230S V2. I have about 4 minutes of flight on the model. My landings were not hard. Each break was near where the tail boom enters the body. After I filled off the broken portion of the boom (about 3 CM),...
thingiverse
I consistently damage the front frame mounting point on my landing gear. Replacing the frame is an inexpensive option, but it's a significant hassle. To resolve this issue, I created a straightforward component that can be secured in place using glue...
thingiverse
Changed the trigger shape to be like a speedball blade trigger (as a request). Made for a V2 greabox. ... If it doesn't seem right, or the angle isn't right, send me a message or feel free to change the design.
thingiverse
This v2 includes: - Flat Emitter - Beveled Emitter - Switch sleeve (no clip) - Switch sleeve (clip attachment) - Switch sleeve button - Hilt - Pommel - D rings - Belt clip As you can see, the biggest changes I made were adding an optional belt clip...
myminifactory
... you are scoring the dough with it. ... This is a new iteration of my previous blade lame with longer uncovered blade length and a bit more sturdy handle. ... To assemble you will need a razor blade, 3 pcs M5 nuts and 3 pcs M5x10 socket head bolts.