blade 120 sr 3d models
73019 3d models found related to blade 120 sr.
thingiverse
This part replaces the stabilizer bar on the Blade 120 SR Helicopter. Use a sanding paper to smooth out the small balls until they fit perfectly into their corresponding slots. ...I'm hoping this will be helpful for everyone who uses it.
thingiverse
This is a battery holder designed specifically for the Blade 120 SR to securely hold a 3.7v, 25c, 600mah battery from ZOP power. I had amassed a large collection of these batteries and immediately saw their potential on the Blade 120SR.
thingiverse
A stabilizing tail fin at the rear is featured in the Blade SR 120 remote-controlled helicopter model.
thingiverse
Here is a rewritten version of the original text: The Blade 120 SR Tail Motor Mount makes it easy to print and install on your aircraft.
thingiverse
I made these skids easy to print fast and without support issues. If you want a more stable stance, you can quickly heat up the ABS plastic using a lighter or heat gun and then gently bend it slightly. The design does not include a bent section, so...
thingiverse
Best printed with open side facing build plate with supports on long post. ...Use brim to keep printer from knocking print off bed.
thingiverse
... and feel free to copy or modify it as needed. The fin used in the photos is the Blade 120 SR Fin, designed by praudt, which can be found on Thingiverse at https://www.thingiverse.com/thing:124535.
thingiverse
... the cutting edge. For transport, the knife should still be in a narrow pocket or wrapped in a cloth. It's more than sharp ;-) Addendum: My 20 year old Mora 120 has a slightly thinner blade (2.5mm), for this the file "Mora_120_Old_Bladeguard" is.
thingiverse
This is a basic wall hanger for the E-flite BLADE SR helicopter. It's 85 mm wide and I believe it will fit some small 200 class helis. Paypal: juribe2@hotmail.com if you want to tip me. ...Thanks.
cults3d
This is a basic wall hanger for the E-flite BLADE SR helicopter. It's 85 mm wide and I believe it will fit some small 200 class helis. Paypal: juribe2@hotmail.com if you want to tip me. ...Thanks.
thingiverse
Rotorblatthalter für Blade 120 v2Es sollten immer beide Blatthalter getauscht werden wegen der auswuchtung
thingiverse
Blade 120 s2 batteryholder. There are some hanging issues when extrusion printing with plain ole PLA which cause the layers to droop, but otherwise, it works. ...
thingiverse
The E-flite Blade SR offers a horizontal fin for your Radio Controlled (RC) helicopter, providing improved stability and control during flight. This essential accessory is designed specifically for the Blade SR model, ensuring a perfect fit and...
thingiverse
https://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: bar_style = surround_text font_narrow_widen = 0 lug_style = plate text_color = DarkRed bar_length_trim = 0 bar_width = 5 writing_direction = ltr...
thingiverse
Yup... once in a while they break. Here is a shiny new replacement set so you can keep flying. Unlike the easy-break OEM part, each replacement skid forms a closed loop and mounts securely with two 3mm x 10mm screws. They are approximately 3mm longer...
thingiverse
This model comes with the "quick install" plate. just losen the screws, slide the previous fanducts out then the new ones in, tighten, that's done ! Before printing, measure the distance between the bottom of the effector plate and the tip of your...
thingiverse
Swapped the stock plastic frame for the carbon-fiber Microheli frame. The plastic parts and dampers that come with that frame disappeared in the yard so I had to make this cradle to mount the controller. Should print out of the box, but will need...
thingiverse
Customized version of http://www.thingiverse.com/thing:46423 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=46423 Instructions Using the following options: - USB cap height is set to 1.25. - The sign type is...