bl touch ender 6 3d models

when I put together my satsana ducts I tried putting the bl touch on but it was to sort so i modeled this spacer to fix it instead of using m4 washers like everyone else

I needed a spacer for my BL touch. I could not find the one i needed so i made one myself. ... You can adjust the z-size to get the desired height of the spacer that you would like.

BL Touch mount to go with Wombot Exilis XL, printed in ABS filament at 0.1200 layer height with 100% infill to go with my other parts. ... See the completed setup at https://www.thingiverse.com/thing:4570236

BL Touch mount to go with Wombot Exilis XL, printed in ABS filament at 0.1200 layer height with 100% infill to go with my other parts. ...See the completed setup at https://www.myminifactory.com/object/3d-print-131035

Hallo zusammen, Wie vielen ging mir das Licht des BL-Touch auf die Nerven! Hier meine Lösung ;) Hält ohne Schrauben einfach aufstecken und fertig. Ich habe das ganze noch schwarz lackiert da mein Filament nicht blick dicht war. ...

Needed mount for BL Touch for 4010 fan on E3D V6 hotend.Based on nice design by user Hairing, sadly there was no +5mm off center version, so I made my own :)

This support allows you to integrate a sensor for self-leveling BL Touch and a female connector type RJ45 for a perfect management cable. No soldering required. ... For Wanhaoo D12.

Tiny adjustment to BL Touch positioning is needed.\r\nStandard layer height set at 2mm, but users can easily adjust this value within their slicing software.\r\nStill under development.

Parts links below: BL Touch 3D Touch Springs 0.4x4x15-20 mm Screws M2 5mm Screws M3 20-25mm Kapton Tape PTFE Adhesive Tape Extruder BMG Aero 4010 Fan LED Links to used tools: Mini Wireless Grinder Polishers Buffers Abrasive Dremel Tools LAOA Mini...

You can pront the pin laying (stronger) or standing (more precise).Installationprint the pinremove bolt on the top of the coil on the BL touchuse long thin rod (hex/allen key) and push the broken pin from the tip of the BL touchremove the original...

This is a remake of the item below:\r\n\r\nhttps://www.thingiverse.com/thing:3348829\r\n\r\nspecifically crafted to accommodate BLtouch cables when they deviate from the main cable route.\r\n\r\nI encountered this issue on my CR10 S5, where the...

I really liked the design of the OP Titan Aero mount, but I wanted to give the BL Touch a shot instead - unfortunately, I didn't find anything that caught my eye, so I decided to print the mount and then modify the IR sensor mount to fit the BL Touch...

With this mount you can assemble the Bl-Touch either on top on on the bottom to use with either normal size or volcano size hotends.There is a hex nut version and an inserts version.Use as you are pleased.Enjoy.

... it didn't mesh well with my print cooling fan(peanut). ...I reworked it, incorporating sleeves for the m3 nuts to be pressed into place. I didn't need any spacers for the bl touch, plug and play functionality. ... M3 - 2 x bolts M3 - 2 x nuts Pliers

I didn't like that removing the fan housing for the hotend would take the BL touch with it on an SV03, and could require to redo z offset, so I made this to attach to the motor/extruder mount. It's kind of a tight fit, and you need a longer m4...

CR-10 / Ender Hotend Cover For Stock Fans With Modified Upper Fan Input and BL-Touch

I loved the sleek design of that effector:\r\n\r\nhttps://www.thingiverse.com/thing:2050626\r\n\r\nBut I had my heart set on using a BL Touch instead of an IR probe, so I made some adjustments.\r\n\r\nWith limited space available on the build plate,...

Shortly after getting my pi cam for octopi setup, I quickly noticed the only thing you could see was the bright, glowing light of the BL Touch. Unfortunately, this light is always on, and there is no way to turn it off in the Marlin firmware to my...

BL Touch holder for my direct drive - it prints flat, without holder, always to be made in PETG. For the BLT iL is fixed with its original screws, for the BLT holder you just have to respect the position as on the picture, you can glue or screw them...

Holder/Mount for BL Touch on the X-Axis-Chain-Carriage-Mount of https://www.thingiverse.com/thing:2105040 . Fix the BL with 2 M3 screws and clip it securely to the bottom of the chain mount. Optionally, secure it further from above using a...

Mount for BL Touch positioned directly above the X Carriage, listed below my current location. Additionally, 2mm shims are included to achieve the precise height of 8.30mm from the hot tip end, ensuring a minimum clearance of at least 15mm from the...

when I put together my satsana ducts I tried putting the bl touch on but it was to sort so i modeled this spacer to fix it instead of using m4 washers like everyone else Print Settings Rafts: Doesn't Matter Supports: No Infill: 60% Filament:...

BLTouch (v3.1) install on a Sidewinder X2There isn’t a lot of published information on whether or not this will work.  I’m accustomed to doing things both wrong and the hard way, so after the probe broke on my X2 I decided it was time to upgrade.The...

The reason I designed this mount to attach to the back and wrap around to the left side was to accommodate the use of this dual fan mount, which disqualified all other BL Touch mount designs. I've included the Fusion 360 file, which contains my...

This is pressure fit to ensure your bl-touch stays clean and string-free, preventing webbing from interfering with the probe pin's movement in its path. Many people encounter issues with their probes sticking, failing to deploy, or becoming...

This is pressure fit to your bl-touch to keep the probe pin clean and to keep strings and webbing from getting into the path way the probe pin moves in Alot of people start to have issues with their probe sticking, not deploying and just becoming...

... slip off mid-print, compromising filament flow. I'd like to extend special thanks to @sneakyninjapants BL Touch Bra on Thingiverse (https://www.thingiverse.com/thing:3762809) whose ingenious idea sparked the creation of this game-changing design.

BLTouch (v3.1) install on a Sidewinder X2There isn’t a lot of published information on whether or not this will work.  I’m accustomed to doing things both wrong and the hard way, so after the probe broke on my X2 I decided it was time to...

Here is a Ender 6 version (with the recesses) of the "new" or "updated" minimus fan shroud backplate. ...4/15/2023

Human Mount Touch