bl touch ender 3 pro 3d models

Printing the original for an Ender 3 usually melts the plastic in my experience, so I tightened down the angle of the blower, lowered and spun it a bit so it's still aimed at the tip of the nozzle, but away from the hotend block enough so it won't...

Hello fellow makers, I made a fan duct for my Phaetus Dragon hotend, dual 4010 part cooling, BLTouch support which fits perfectly on the Ender 3 gantry.What you need:Phaetus Dragon Hotend1 or 2 4010 Blowers4010 cooler (1 used a Noctua)Ender 3 Gantry...

Set the Z offset by flipping the power button or manually touching the probe gently to simulate it touching the bed. 2. Run G29 to do an autobed level probe and save the settings to EEPROM with M500. 3. Check that the printer is working correctly by...

This is a remix of the default Creality mount. ...Offset to allow for use with direct drives. You may need to force the screws a bit or lightly drill them a touch wider.

Made a remix with the following desingns https://www.thingiverse.com/thing:4960249 https://www.thingiverse.com/thing:5141820 https://www.thingiverse.com/thing:4736330 Made this so i can easy change the nozzle and still have the CR touch and laser...

Made a remix with the following desingns https://www.thingiverse.com/thing:4960249 https://www.thingiverse.com/thing:5141820 https://www.thingiverse.com/thing:4736330 Made this so i can easy change the nozzle and still have the CR touch and laser...

Quick clip I made to channel cables on CR10S-Pro upgrade. ...Add a magnet into the bottom and can attach on base and up frame if required.

I adjusted the height of my printer to match my nozzle's positioning, ensuring a smooth build process on my trusty CR10S-Pro.

Edit 3/2/2020: Noticed Front Wire Tray Issue and Posted Updated Files for Motor Clearance. Added Hole Counterbored for M3 Buttonhead Screw on Unused Fourth Motor Mount, Potentially Used as Temporary Motor Holder During Assembly. This is a Modified...

I used 20% infill and 3 perimeters but that's just what my printers are tuned for. You can get away with no supports if your printer can do a few overhangs. ... tips: Turn the printed mount counter-clockwise while tightening bolts It's easier...

... in tinkercad You should be able to print this at its orientation, support is built in and made to be broken off. x_offset: -35 y_offset: 0 z_offset (for my probe, you will calibrate this) = 3.220 added new version with no builtin support. ...

Lake for Mother Cutout for metal from Fan Mounting Bracket

To use with: BLtouch: https://fr.aliexpress.com/item/1000006359561.html?spm=a2g0s.9042311.0.0.27426c37HnZy5G LED Strip: https://fr.aliexpress.com/item/32843070878.html?spm=a2g0s.9042311.0.0.27426c37WjQh8V X and Y Offsets #define...

its for peaple that use the spider hotend

This is a BLTouch mount that relies on two bolts, with one being the roller bolt. ...It proves to be extremely useful when working with a volcano nozzle, particularly depending on the specific volcano mount in use.

The original design was downloaded from Grabcad, where it was intended for a CR-10 but also works great with an Ender-4. Original Design: https://grabcad.com/library/cr-10-e3d-v6-hotend-mount-and-fan-duct-1 This mount is specifically designed to be...

The actual DDX does not fit exactly by default for the Ender 6 - you will beed to manually cut some parts as it clashes with the v-wheel screws. However if you have done that, you will also find their BLTouch holder will not fit properly as well. ...

V2 Update: I added a bit of Material behind the right Hole, and i took the guard near the Heater of the Nozzle away, where the LED Panel was, and i extended the Hole for the Hotend Heater Cable.Thx for the Thing, i print my Remix tomorrow to see if...

I made an enclosure for my Ender 3 S1 Pro and wanted to put the controller outside for easy manual control... (I might build an Octoprint RPi enclosure with switching relays etc at some point as one larger unit integrating the touch control...). ...

... setups. This can be printed in PLA. But PETG is recommended for longevity. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: 0.2 Infill: 75% Filament: eSun PETG White Category: 3D Printer Accessories

- Place the assembly on the Ender 3/Pro and start both screws but don't tighten yet. - Press down firmly on the area below the LCD but just above the mounting screws so that the cut away on the back is held against the aluminum extrusion. - Then...

I also wanted it to sit in line with the Y-Axis of the printer nozzle.Offsets for the prove are X: 39 and Y: -1 (Z offset should be the same as the stock mount location)I'll link my Noctua 40x40 fan mounts as I finish them as well.UPDATE:...

CR Touch offsets are : x_offset: -46.5 y_offset: 0 Hardware for CR-touch probe: 2x M3 nuts With KLIPPER You can modify the offset in the "printer.cfg" file: [bltouch] x_offset: -46,5 y_offset: 0 You may also need to adjust your mesh if you get an...

This is a remix of the designs from: https://www.thingiverse.com/thing:4740250 https://www.thingiverse.com/thing:4966561 https://www.thingiverse.com/thing:4749419 I have updated the following: - Updated the components to work with the Biqu H2 V2 with...

This is a remix of the designs from: https://www.thingiverse.com/thing:4740250 https://www.thingiverse.com/thing:4966561 https://www.thingiverse.com/thing:4749419 I have updated the following: - Updated the components to work with the Biqu H2 V2 with...

This is a remix changing the magnet orientation in order that the magnet is facing the Touch Mi.

If the two mounting holes are too small for the bolts, adjust the hole offset in your slicer so it prints the files appropriately (you can calibrate to find your needed offset by printing a tolerance test).No supports needed.Setup:You'll need to...

I can ensure you that the CR touch mount is at the correct height, and you wont be digging your nozzle into the build plate. I also added an additional support to prevent the CR touch mount from flexing when probing. It's not pretty... but it...

... nut is a little tricky to get in place, but trust me, it does fit). Possibly could be used with the provided screws with the CR Touch. ... Also, here is what I got for XY Probe offset: -50, -15, 0 (I'm sure it's not perfect, but its working great)