bl touch ender 3 pro 3d models

Functional mix between #3584158 and #4336829

Remix of this direct drive mount: https://www.thingiverse.com/thing:4428109 I have changed the setup of the mount with a personalised duct that allows to install a Noctua fan or any other 40mm fan. In addition, I have slimmed down the motor...

Simple and solid holder for BL Touch for Ender 3.

Remixed the BL touch design so it'd sit closer to the nozzle. ...With this design the drag chains I installed on my printer don't run into the vertical bars. x-offset: -42.10 mm y-offset: -17.00 mm z-offset: (take this with a grain of salt and adjust...

Unfortunately, the screw on my BL touch had worn out too much to adjust the height of the measure tip. ... As a substitute for the original sensor, I used this clone from Aliexpress: http://bit.ly/2McIHrB The approximate offsets for the new sensor are...

Remixed the BL touch design so it'd sit closer to the nozzle. With this design the drag chains I installed on my printer don't run into the vertical bars. ... x-offset: -42.10 mm y-offset: -17.00 mm z-offset: (take this with a grain of salt and...

I adjusted this to work with a BL Touch

I couldn't find a BL Touch bracket for my Ender 5 Pro that would print properly and modifying existing brackets revealed some weaknesses and showed the Y axis belt crimp would contact the probe. I ran up a new setup based loosely on the bracket I...

This is a Mounting Plate for the Revo Hemera XS with BL-Touch + 4020 Fan. ...It fits on Creality Ender 3 / 3 Pro / 5 / CR-10. ... Enjoy ;)

The BL touch set is now configured specifically for use on an Ender 3/5.

Simple yet effective bl-touch mount for creality ender 3 v2 (becouse one that came with bl-touch fits only ender 3 v1). No need for additional parts, nuts or screws. ...Works perfectly with original set of screws.

Simple but sturdy bl-touch mount (becouse one that came with bl-touch fits only ender 3v1)

I made this BL Touch mount is because there is no suitable mounting for the Ender 3 Max printer. You will need 2 x M3 Bolts and 4 x M3 Nuts, the two extra M3 nuts replace the spring that comes with the BLtouch to enhance the stability and accuracy...

BL-Touch mount for the Ender 3 V2. I made four version, two round screw and two nut head screw version. The print is support free. Probe offset for the firmware: X = -42, Y = -10 Z-offset is -0.96 for me. ... Additional parts needed : M3x6...

... close to the original position as possble. I was also able to put a BL-Touch closer to the nossle as the standart Ender 5 plus's position. I am not happy with the fan duct but it does the job for now. ... ...feel free to remix the sh** out of it.

Filament Cooling Width Now Features Integrated BL-Touch Support

Modified Version of the Creality Ender 3 S1 Shroud with the BL Touch and CR Touch mount moved to the right side Update 1: Added the hole for the gear tensioner back and missed the gab for the metal backet to slot into Update 2: Fixed some...

Voron Afterburner Gallileo Clockwork mount plate for Creality Ender 3 / CR printers with bl-touch and accelerometer (ADXL345 or similar) mount. (fits 1.5 version of official orbiter kits but you need addtional 1pc MR 148ZZ bearing) Full area of...

Compact BL Touch mount for the Ender 3 V2 Initial version (my preference, unless you use the Creality firmware and don't want to update the offset): Offset X = -39, Y = -7 Version with correct offset for Creality firmware: Offset X = -45, Y = -20...

This is a fan shroud for Ender 3 Pro that fits 40x20mm cooling fans like Sunon or Noctua, and it's fully compatible with the stock mounting screws, fan, and duct. I printed this out of PLA without any issues with warping or melting. To ensure a...

Here's a plotter that you can use without removing the BL touch Only needs one screw Only works with bic crystal though

I designed the lightest fan duct possible, to be printed without support, adaptable to stock fans and compatible with direct drive and BL-Touch. ...Enjoy !

Ender3 BL Touch Mount with M3 Hex Nuts (5.5mm A/F) held in, to use original screws included with the Touch the offsets should be aroundx=-40.5 Y=-6.5Printed In ABS

BLTouch mount for Ender 3 Max

Hope this helps someone who needs the bracket who already has the BL touch sensor. I think this may fit a CR10 V2/V3 as well, but not 100% This is my first item design, so please let me know it it works for you. ... If you find this useful, please...

This will retain the use of a the Steel BL Touch Kit from Creality, this will probably work with a CR Touch kit as well that uses the steel mount. You will need to extend the extruder stepper cable for this to work This will work with the stock...

The original file does not include a mounting bracket for the BL-touch probe; therefore, I created an alternative to facilitate assembly. ...It is recommended that you print this component using ABS material, but PEGT and PLA also produce satisfactory...

This is remixed from https://www.thingiverse.com/thing:4762570 with a height of 29mm. ... With the origin part the nozzle was to far away also for Z correction (Ender 3 max). ... This part with a height a of 25.4 mm works perfect in my case.

A remix of the Ender 3 V2 BLTouch mount originally published by Bertram69, link: https://www.thingiverse.com/thing:4563093. The original part did not fit my printer without filing, so I simply added a cutout to make room for the wheel bolt head. ...

This adjustment ensures that your touch is aligned properly to prevent it from dangling precariously off the edge of the bed as it makes contact.