bl touch ender 3 pro 3d models

This support allows you to integrate a sensor for self-leveling BL Touch and a female connector type RJ45 for a perfect management cable. No soldering required. ... For Wanhaoo D12.

I needed a spacer for my BL touch. I could not find the one i needed so i made one myself. ... You can adjust the z-size to get the desired height of the spacer that you would like.

Needed mount for BL Touch for 4010 fan on E3D V6 hotend.Based on nice design by user Hairing, sadly there was no +5mm off center version, so I made my own :)

BL Touch mount to go with Wombot Exilis XL, printed in ABS filament at 0.1200 layer height with 100% infill to go with my other parts. ...See the completed setup at https://www.myminifactory.com/object/3d-print-131035

BL Touch mount to go with Wombot Exilis XL, printed in ABS filament at 0.1200 layer height with 100% infill to go with my other parts. ... See the completed setup at https://www.thingiverse.com/thing:4570236

Tiny adjustment to BL Touch positioning is needed.\r\nStandard layer height set at 2mm, but users can easily adjust this value within their slicing software.\r\nStill under development.

when I put together my satsana ducts I tried putting the bl touch on but it was to sort so i modeled this spacer to fix it instead of using m4 washers like everyone else

I just wanted my ender 3 to have some legs. ...Making them tall enough to place a spool of filament under the printer is a plus too.

BLTouch (v3.1) install on a Sidewinder X2There isn’t a lot of published information on whether or not this will work.  I’m accustomed to doing things both wrong and the hard way, so after the probe broke on my X2 I decided it was time to...

buy this and ender website

I made a quick holder for half of a Penn Ultra Blue Racquet ball https://www.amazon.com/Penn-Ultra-Blue-Racquetball-Ball-Can/dp/B002LGF9L6/ref=sr_1_6?dchild=1&keywords=Penn+Ultra+Blue&qid=1598666340&sr=8-6 This is all I had available at my local...

I've been putting in some serious time working on an enclosure for my Ender 3 Pro, and I'm finally done with it. This enclosure is different from most others because it's still a single piece when combined with the printer itself. One of its key...

Parts links below: BL Touch 3D Touch Springs 0.4x4x15-20 mm Screws M2 5mm Screws M3 20-25mm Kapton Tape PTFE Adhesive Tape Extruder BMG Aero 4010 Fan LED Links to used tools: Mini Wireless Grinder Polishers Buffers Abrasive Dremel Tools LAOA Mini...

I converted my Ender 3 to direct drive so I decided to place a BME280 in the place of the extruder... ...It is meant to be used with a enclosure but anyways =D

You can pront the pin laying (stronger) or standing (more precise).Installationprint the pinremove bolt on the top of the coil on the BL touchuse long thin rod (hex/allen key) and push the broken pin from the tip of the BL touchremove the original...

This was modified to attach both the BL Touch and the Creality laser to the Ender 3 Pro.

Holder and adapter for P.I.N.D.A by Prusa for Ender 3 PRO instead of 3D Touch. ... You need: - M3x10 bolt - M3 square nut Firmware settings: #define NOZZLE_TO_PROBE_OFFSET { -44, -31, 0 }

This is a remake of the item below:\r\n\r\nhttps://www.thingiverse.com/thing:3348829\r\n\r\nspecifically crafted to accommodate BLtouch cables when they deviate from the main cable route.\r\n\r\nI encountered this issue on my CR10 S5, where the...

I really liked the design of the OP Titan Aero mount, but I wanted to give the BL Touch a shot instead - unfortunately, I didn't find anything that caught my eye, so I decided to print the mount and then modify the IR sensor mount to fit the BL Touch...

BLTouch (v3.1) install on a Sidewinder X2There isn’t a lot of published information on whether or not this will work.  I’m accustomed to doing things both wrong and the hard way, so after the probe broke on my X2 I decided it was time to upgrade.The...

I swapped out the Ender 3's gears for a direct drive setup, and next I'm placing a BME280 sensor right where the extruder used to be. ...The plan was to use it with an enclosure, but that's not necessary.

... it didn't mesh well with my print cooling fan(peanut). ...I reworked it, incorporating sleeves for the m3 nuts to be pressed into place. I didn't need any spacers for the bl touch, plug and play functionality. ... M3 - 2 x bolts M3 - 2 x nuts Pliers

I didn't like that removing the fan housing for the hotend would take the BL touch with it on an SV03, and could require to redo z offset, so I made this to attach to the motor/extruder mount. It's kind of a tight fit, and you need a longer m4...

CR-10 / Ender Hotend Cover For Stock Fans With Modified Upper Fan Input and BL-Touch

Shortly after getting my pi cam for octopi setup, I quickly noticed the only thing you could see was the bright, glowing light of the BL Touch. Unfortunately, this light is always on, and there is no way to turn it off in the Marlin firmware to my...

I loved the sleek design of that effector:\r\n\r\nhttps://www.thingiverse.com/thing:2050626\r\n\r\nBut I had my heart set on using a BL Touch instead of an IR probe, so I made some adjustments.\r\n\r\nWith limited space available on the build plate,...

Solder-less Design Ender 3 (270mm printing height): Print 2x, one for each side Ender 3 (370 print height extension): Print 4x, 2 for each side Approximately 24 LEDs per side (48 total) Instructions: In order to utilize this one, you will need to...

E3 Pro Mini! If the file comes out huge, scale to 40% works good. ...I would like to see some makes!

The original mount holds up well but for my replica of the 3D Touch, I found that the placement was slightly too low down. In contrast, my modified version sits 1mm higher. I printed this using PETG with a solid 100% infill and a buildplate support...

Printing Instructions Regardless of version you go with, the following print needs still apply unless otherwise stated Standard ender 3 (270mm Print height): 1x of the chosen style per side Ender 3 z-axis Upgrade 500mm (370mm z-axis Print Height) 2x...