bl touch ender 3 pro 3d models

Mount the China BL touch on the Ender 3 Pro's endstop bracket securely with screws provided. Then, print a small glue holder at a thickness of 1.5 mm using iron plate material. ...Mark the holes for mounting the glue holder and carefully drill them into...

A more rigid version of the BL-Touch mount for the Ender 3 Pro Fang Duct. Printed with Tree Supports and high infill. Edit: After printing I noticed that the part is slighty to large. The side of the upper support tentacle touches the...

... датчика авто-уровня BL Touch. ... Не мешающее не чему! Обновлено: 15.01.2022 * Мод под вплавляемые гайки (M3 X D5.0 X L4.0) https://aliexpress.ru/item/4000232858343.html * Усиленная версия крепления BL-Touch https://aliexpress.ru/item/32832887426.html

There is 4 nuts places in `ender-3-mount.stl` and single in `extruder-back-mount.stl` As you can see this design allow you to print even 85˚ overhangs. Not good but possible. All angles below looks pretty good and starting from 70˚ is good enough for...

(At least on the Ender 3 V2 with the Sprite Pro extruder) You would then set the endstop position to keep the nozzle zero above the build plate. The fit is good, you will need slightly longer M3 screws than the ones originally used to mount the...

I modified the part to fit the Ender 3 Pro with or without the BL-Touch Metal Bracket.

I modified the part to fit the Ender 3 Pro with or without the BL-Touch Metal Bracket.

I modified the part to fit the Ender 3 Pro with or without the BL-Touch Metal Bracket. Category: 3D Printer Parts

BLtouch mount for Ender 3 Pro Microswiss Direct Drive kit, offsets the BLT 60 degrees, enabling you to take the standard Ender shroud off without removing BLT.

This is a combo shroud that allows you to mount both a Noctua NF-A4x20 FLX 40mm fan and a BL-Touch auto-leveler to your Ender 3 Pro. You will need four M3 screws (approximately 1.5 cm in length) and nuts in order to secure the fan to the shroud.

I recently purchased this sensor:...

Finally, I added a mount for a BL/CR touch. I have had some issues with it running into the X-axis stepper motor mount, but I solved that by removing the mount entirely and printing an adjustable X-axis endstop mount. You may need to add a couple...

I really liked the mount designed by bilbs84 but when I printed and mounted it, the bottom didn't sit up close to the Sprite Pro, and thus the probe was at an angle. I decided to remix to mount with 4 bolts instead of the two. ... Hardware you'll...

 I upped the perimeters to 4 and upped a gyroid infill to 50% for more stiffness.BL Touch offset (z offset is approximate) * +-- BACK ---+ * | [+] | * L | 1 | R <-- Example "1" (right+, back+) * E | 2 | I <-- Example "2" ( left-, back+) *...

... All Metal Hotend" (or clone). ...This type of hotend is a little bit shorter than the stock hotend of the Ender 3 (Pro), so with the stock mount the touch pin can not be fully deployed. ...I had printed it with PLA Carbon, because it's stiffer.

... All Metal Hotend" (or clone). ...This type of hotend is a little bit shorter than the stock hotend of the Ender 3 (Pro), so with the stock mount the touch pin can not be fully deployed. ...I had printed it with PLA Carbon, because it's stiffer.

Added a bl-touch mount to the bracket from https://www.thingiverse.com/gpshemi https://www.thingiverse.com/thing:4728724 Changed the design a little. Made the mounting plate a bit thinner at the mount area and added honeycombelements. ### I...

Remix of ebyaskawa Ender 3 Pro Umbilical Support Bracket. ...I only added bl touch mount to it.

It is processed to fit perfectly on stock Ender 3 Pro. Due to the fragile nature of the initially design of the BL Touch mount, it was remixed into more strong one.. Both turbine fans are wired into one socket to the board.. Optional printing...

This design brings the BL touch very close to the nozzle and accommodates two 40mm fans for good cooling. I run the hot end cooler blowing outward "away" from the printed parts. The design is meant to have 3mm brass melt-in inserts where...

... Im going to add Cable clips and possibly mount for a LED light and maybe ill lower the camera a little bit more!NO BL/CR TOUCH! ...Probe sticks out and hits the shroud, Need to cut out a section to clear Thanks OPCategory: 3D Printer Accessories

hi, i was looking for some cr touch bracket, but i've cannot find anything good for my ender 3 pro with satsana fan duct already printed. here you can try this on yours ender 3/3pro. be carefull! at first you have to carefully set the X axis...

Extruder knob for Creality Ender-3 v2 and Ender-3 Pro, Tension Knob, BL-touch mount

... gap for the hot end a bit bigger. I also added the adjustable BL Touch mount. Hardware: 2x M3 bolts for BL touch mount 2x M3 bolts for BL touch probe 2x M3 nuts for BL toouch probe 2x M3 washers for BL touch probe Settings: Offset is {-50 , -20 }

The design has the bl-touch integrated into the mounting plate this idea came from (https://www.printables.com/model/139183-ender-3-v2-voron-stealthburner-conversion). but I had to redesign the whole thing as his did not fit the Stealthburner if you...

The design has the bl-touch integrated into the mounting plate this idea came from (https://www.printables.com/model/139183-ender-3-v2-voron-stealthburner-conversion). ...but I had to redesign the whole thing as his did not fit the Stealthburner if you...

The design has the bl-touch integrated into the mounting plate this idea came from (https://www.printables.com/model/139183-ender-3-v2-voron-stealthburner-conversion). ...but I had to redesign the whole thing as his did not fit the Stealthburner if you...

Functional mix between #3584158 and #4336829

Remix of this direct drive mount: https://www.thingiverse.com/thing:4428109 I have changed the setup of the mount with a personalised duct that allows to install a Noctua fan or any other 40mm fan. In addition, I have slimmed down the motor...

Simple and solid holder for BL Touch for Ender 3.