bl touch cad 3d models

... accommodate heat-set inserts, which made adjustments a lot easier. The brass threads on these inserts really helped. The BL Touch mounting holes are designed specifically for the M3-0.5 tapered ultrasonic insert, available at globalindustrial.com.

By employing this design, users can effortlessly park the nozzle tip on the lower surface and fine-tune the stowed BL Touch probe until it makes contact with the upper block. To verify the flatness of the probe's surface at a distance of 8.5...

When assembly I realise there was not enough clearance for BL Touch mount so i use 10mm m3 standoff to get rid of this problem. Also didnt think about x endstop when designing mount so temporary using y endstop mounh of original hypercube for x axis....

I want to install a Cobra fanduct on my AM8 with E3DV6 and I'm having trouble putting the BL TOUCH sensor in at the same time, so I designed a support for my BL TOUCH sensor to go behind the print head. The mount attaches directly to the aluminum...

I created this part because I couldn't find any BL Touch support system for AlfawiseU20 or CR10. Two sliding parts. This way the HotEnd remains accessible. Printing made in ABS (more heat resistance) then smoothing with Acetone (a little bit more...

I'm designing a custom dual blower mod based on other Hypercube E3D v6 mounts, but with a twist - it incorporates a BL Touch sensor behind the nozzle for precise part cooling and features two blower fans for enhanced part cooling capabilities. To...

This bracket can be disasembled from the hotend cariage without having to take the BL-Touch of the bracket, making it more maintenance friendly! IMPORTANT... Print it with support to build plate! ...There are slots on the bottom to fit it flush over the...

I recently changed to a Titan Aero, but wanted a bracket for my BL Touch, but I could not find any stand alone brackets so opted to design one, this mounts off the fan, and puts the BL Touch in line with the nozzle and 41mm in front. I designed mine...

To securely fasten this mount to either the 2020 ExoSlide or the 2040 model, you will need to use M4x12 (extruder and timing belt retainer), M3x8 (BL Touch), and M2x8 (fan mount) cap screws. ...The required quantity differs depending on your chosen...

This is an extra 3d printed part to HANSMANN's Eryone Dragonfly BMS The original does not support 3D touch or BL touch. ...Use this to mount it M4 Nut is required to lock the screws holding the 3D Touch

***[DEPRECITATED]*** ___updated design available here:___ https://www.thingiverse.com/thing:5389810 Remix of the Manta MK2 BL Touch Central Mount with added holes to fit M3x5.7mm heat set inserts for mounting an ADXL345 IMU. Using this sensor, any...

This is a custom BL Touch mount designed for Prusa i3 x carriages, specifically tailored to accommodate bowden setups with modified E3D V6 hotends. To optimize the print process, lay the top mount surface directly over the bed, reducing unnecessary...

I get fed up of having to reset the Z offset each time i remove the fan shroud for cleaning/maintenance etc so i cut off the lugs that share the same screws so the BL Touch stays mounted when the fans are removed. ... The M5 bolt that sticks through the...

I needed somewhere to mount my BL touch so modified this design. There's no adjustment so you just have to dial it in with the software offset (I use 3mm). I should add, i didn't like seeing the label on the fan so i modded it so it's the other...

This is a custom mount designed specifically for the BL-Touch on the JG Aurora A5 3D printer. It's been expertly integrated with a cooler enclosure to enhance performance and stability. When installing, be sure to replace the original screws with...

The adjacent part to secure the actual BL Touch sensor can be found here: https://www.thingiverse.com/thing:3148733 (adj-bltouch-mount-3D-wing.stl). Although it's not flawless, this mount enables attachment of the sensor to the printer itself. Two...

... close to the original position as possble. I was also able to put a BL-Touch closer to the nossle as the standart Ender 5 plus's position. I am not happy with the fan duct but it does the job for now. ... ...feel free to remix the sh** out of it.

- Added custom bl-touch mount rotated cables out to make space/avoid collision with extruder wiring and gain some reach on left side of X - Heat inserts for Bl-touch and ADXL mounting - Still in progress will add customized cable cover with cable...

This is a customized BL touch mount specifically designed for the SainSmart Pioneer 3D printer, which has its roots in the Xvico Pioneer. ... Here are the offsets that have been set in Marlin for my setup: #define X_PROBE_OFFSET_FROM_EXTRUDER -42 // X...

I get fed up of having to reset the Z offset each time i remove the fan shroud for cleaning/maintenance etc so i cut off the lugs that share the same screws so the BL Touch stays mounted when the fans are removed. ... The M5 bolt that sticks through...

This innovative mount is equipped with several essential components: * A Built-in BL Touch Module for precise calibration * A Standard Fan Duct for optimal airflow * A Standard Fan Mount for easy fan installation * A T-Slot for future add-ons, such...

I needed somewhere to mount my BL touch so modified this design. There's no adjustment so you just have to dial it in with the software offset (I use 3mm). I should add, i didn't like seeing the label on the fan so i modded it so it's the other way...

I was in dire need of a BL Touch mount for my Anycubic Kossel that wouldn't collide with the rods and would only cover the upper half of the 40 mm hotend fan. After some careful consideration, I decided to design one myself. ...The resulting mount is...

Two versions of the center mount for the BL Touch + ADXL343 or ADXL345 sensor. Both sensor versions have different screw fitting. One is screwed directly into the plastic, this is only suitable if you plan to keep the sensor on the print head. ...I...

... CR-10 V2 hot end. It positions the probe precisely, and our firmware features a CR-10 V2 / BL Touch toggle. The hex file is available in the files section. ... Source Code: https://github.com/InsanityAutomation/Marlin/tree/CrealityDwin2.0_Bleeding

This is a mount for a BL Touch on an A8 Plus. I had found a number of alternative methods, but all looked a little flimsy with a large cantilever. This is Easy to print Easy to mount Strong Integrated cable management I have produced two versions:...

I created this stain relief part to securely fasten the bl-touch cable. I firmly attached it to the bracket that supports the bltouch for my cr-10 by shocksofmighty. I am releasing this design into public domain, allowing every individual to freely...

I saw a few CR-5 users wanting to upgrade to the Pro H BL touch. I have not printed this myself and am unsure if HT materials will hold up. I can update this later with a thermal test on the surface of the carriage. ... For now though, test at...

Wanting to mount a BL-Touch V3.1 on my Creality CR-10 Mini i did not find a mount with the desired height and stability so i decided to design my own. It is much more stable because it also 'clamps' around the Extruder-mount back-plate. Furthermore...

I've taken a popular BL Touch mount design from Thingiverse, specifically this one: https://www.thingiverse.com/thing:3148733. The original model required an M3 nut, but I didn't have one handy, so I reduced the hole size and simply used the bolt to...