bl touch anycubic mega s 3d models

I attempted utilizing the original design and encountered issues with the BL Touch failing to strike the bed prior to the nozzle crashing, plus the mount was relatively delicate. To mitigate these problems, I modified it slightly to sit lower, and...

Bonjour, Voici un support pour installer un BL Touch sur la Ender 3 V2, bvous trouverez aussi une mire de vérification du nivelage du plateau adaptée à la Ender 3. J'explique tout dans ma vidéo. ... Ce support est un remix du support :...

Then you can attach the BL-Touch using the springs to create an adjustable mount. Put the springs between the BL-Touch and the mount. Then you can adjust left-right tilt by tightening and loosening one side. You can adjust overall height by changing...

The X Cover BL Touch for the original lost about 1 inch of bed from the left side of the X-axis I did a really crappy fix up so that i could get the full bed on my ender 3 pro again. Cover is done as a quick hack job but 100% works and fits my...

A mount to hold a BL Touch Sensor to an Anet A8I needed a mount that would hold a BL touch sensor to my stock Anet A8 carridge. This design works using the fan mounting holes on the front of the carridge (the fan is then screwed back in place over...

Then you can attach the BL-Touch using the springs to create an adjustable mount. Put the springs between the BL-Touch and the mount. Then you can adjust left-right tilt by tightening and loosening one side. You can adjust overall height by changing...

BL Touch mount for the stock Folgertech FT5 hotend. The mount fits in the two bottom spaces between the hotend fan and the heatsink. No additional screws are required. ... From the CAD model, the nozzle to probe offsets are: X: 40.5 mm Y: 15 mm ...

A Remix of andrzejels "Geeetech 3D Touch Shield" https://www.thingiverse.com/thing:3569989 I made it conform to the 3D touch better.

A Remix of andrzejels "Geeetech 3D Touch Shield" https://www.thingiverse.com/thing:3569989 I made it conform to the 3D touch better.

User initiates a 3D touch to trigger a basic interaction and verify that system responds accordingly.

... in and you should have some adjustment. ... i also have included a jig to help align the Bl touch to 8mm below your nozzle, just put the pin of BLT in the hole and then adjust the height of the BLT until the nozzle is touching the arm of the jig.

The hotend is designed specifically for use with the AlfaWise U20 Touch 3D printer as well as the BLTouch.

Unfortunately, the screw on my BL touch had worn out too much to adjust the height of the measure tip. ... As a substitute for the original sensor, I used this clone from Aliexpress: http://bit.ly/2McIHrB The approximate offsets for the new sensor are...

Tevo Tornado BL Touch for stock fans or what have you. Installing this I use a Z -0.8 offset. Print slow. All infill. Make it the strongest print you can. Zero flex is the goal. PLA to start but aim to make one from ABS or PETG. Make two once you get...

This fan duct for the ItWorks3D Titan Aero tool head has been modified to mount the BL Touch sensor, as well as having been lowered by 3mm to better aim the air at the print. There is very little room to adjust the height of the sensor, however there...

This is a BL touch mount I made for the Voxelab Aquila. ...I made it specifically to work with the Mini-me V4.&nbsp;</p><p>This is a link to the hot end shroud: <a...

Installation du BL-Touch sur l'Artist-D : Utiliser des inserts M3 à sertir à chaud pour fixer le BL-Touch. Utiliser un cablâge 5 fils comme montrer sur les photos. Installer un connecteur JST XT 2.54 pour les signaux du Z-offset (fil blanc et fil...

This is my initial attempt at designing a BL Touch Mount for the Crane Quad. First version of this works but is running into one of the extruder motors. I wanted to get something out there for people to experiment with and modify. <u>V2</u> Broke...

Tevo Tornado BL Touch for stock fans or what have you. Installing this I use a Z -0.8 offset.</p> <p>Print slow. All infill. Make it the strongest print you can. Zero flex is the goal. PLA to start but aim to make one from ABS or PETG.</p> <p>Make...

Remixed the BL touch design so it'd sit closer to the nozzle. With this design the drag chains I installed on my printer don't run into the vertical bars. ... x-offset: -42.10 mm y-offset: -17.00 mm z-offset: (take this with a grain of salt and...

A straightforward fix for integrating the 3DTouch feature into your Anet A2 Plus printer involves connecting it directly to the machine's interface board. This can be achieved by attaching the sensor wires to specific points on the board, as...

This versatile card holder is designed specifically for Anycubic's I3 Mega S 3D printer. ...The unique feature of this card holder is that it can be mounted without removing a single screw, making installation quick and hassle-free.

Remixed the BL touch design so it'd sit closer to the nozzle. ...With this design the drag chains I installed on my printer don't run into the vertical bars.</p> <p>x-offset: -42.10 mm<br/> y-offset: -17.00 mm</p> <p>z-offset: (take this with a grain...

BL Touch for the AdimLab Gantry with the extruder in the photo. It replaces one of the LED strip mounts at the bottom of the extruder. ...I have tested the model that works with the Volcano Hotend.</p> <p>The Shorter one (untested) can be used with the...

Extruder cover for anycubic mega-s / pro. You can mount a laser module for mega-pro. The laser module for mega-pro runs at 12V, so wiring It can be controlled by the M106 cord by processing it and replacing it with the connector of the cooling fan...

... to convert my Makergear M2 printer to the e3d hotend and added a BLTouch sensor to auto level my scewed printbed. ... The part for mounting the cooling fans, I printed with my ANYCUBIC Photon Mono resin printer, the rest I printed on the M2 with pla.

Remix of Alternative mount adapter for BLTouch (3D touch) by R4iNER https://www.thingiverse.com/thing:4564617 Easy print no support need - not tested yet.

This is a remix of FlyMike's Anycubic i3 Mega runout sensor reverse housing, with gratitude for the excellent housing components provided. ...The design was modified to fine-tune the switch sensitivity and incorporate a filament guide to maintain...

This is a cable holder for the Anycubic Mega-S printer. It is placed in front of the extruder Motor. Fillament and cables will no longer rub against each other. The cable is held and in a good and tight position. The holder is very strong. ... To...

... Version 2 to address those problems. If you have any additional suggestions for improvements, please share them with me. The fact that it's being used on a friend's printer makes it difficult to gauge its advantages and disadvantages firsthand.