bl touch alternative 3d models

Designed specifically for the BPS V3 Extruder, this 40mm Nema 17 Mount provides a solid foundation for your printer's most critical component. By incorporating spacers or springs, you can ensure a secure and stable fit that withstands even the...

<p>&nbsp;There are two options—one with supports that are easy to cut out and one without. &nbsp;I did the supports because I thought it would be stronger if it was printed lying down. &nbsp;The holes for the BLT are small on purpose so that the...

New Arm designed with consideration for a bolt it strikes, slightly larger in size. ...Trim the lower portion to achieve a more streamlined look.

A feature that automatically adjusts the printer bed height in RepRap 3D printers is called Sensor AutoLeveling.

- Added 2 holes to secure the cover with the screws - Added a mirrored version to mount the cover on the right side

Thanks "JF Keres" for providing me with a solid foundation to build upon. For Geeetech A10M, I'm confident it could also work seamlessly on the A20M model. ... I highly recommend checking out this fan duct: https://www.thingiverse.com/thing:2563670

Voron Switchwire x-carriage w/ heat set holes for an external mounted BLtouch.BLtouch is to sit to the left; added a regular right carriage to keep it even.test fit looked good, but fried my BLtouch before function testing. Got the measurements from...

The mounting system demands new carriage bolts to be installed at the base, specifically the two lower bolts must be swapped out for extended versions measuring 50 millimeters.

Voici un support pour améliorer l'estetique du câblage .

The device is called the Fang Alfawise U20.

This redesigned model, created by CDRSKULL, boasts improvements over the original, but unfortunately, it has yet to be uploaded. ... To assemble this unit on your printer, you'll need two M3 x 12mm pan head screws, which will provide a secure and sturdy...

Remixed from: https://www.thingiverse.com/thing:4533682 https://www.thingiverse.com/thing:3251530 (linking source-files doesn't work for me, fixing problems takes weeks on this site) To use with: https://www.thingiverse.com/thing:4533682 ...

Thinner panels make it possible to slot it seamlessly behind a standard Bullseye duct.

Simple Brush Mount

I found the included BLTouch mount was either too tall on the top hole, or too short on the bottom for me. ...So I extended it a bit :)

I added two new models, one with a thickness of 2 mm and the other with 2.5 mm. ...The 2.5 mm model turned out to be quite sturdy.

I liked the hex light ports on the original but the BLTouch has a very bright Red light that is a bit annoying. Especially on a web cam. ...So I plugged the front holes and left the sides open.

Remix of BLTouch Cover by Csewell on Thingiverse: https://www.thingiverse.com/thing:4415728 The original fits great and I used it for a month, but I still felt there was too much LED light leaking and affecting photos/videos, so this has a little...

These are the parts I designed to convert my Makergear M2 printer to the e3d hotend and added a BLTouch sensor to auto level my scewed printbed. ... The part for mounting the cooling fans, I printed with my ANYCUBIC Photon Mono resin printer, the rest...

this shouls work with m3 screws with no nuts

I'm still unsure if my teeth are straightened, I haven't had a chance to check yet, but I'll know for certain once I get my mouthguard printed. ...It's already getting quite late, which is why I haven't been able to verify it yet.

I didnt have room for a BlTouch with a new Fanmount so this was my only Solution to mount it The Version with Pin has a guiding Pin in the corner for easy installation You need 1x M3 Nut (preferably a Nylon Lock Nut) and one sliding bltouch...

I didn't care for the spacing or positioning of the BLTouch sensor brackets that came with the ANet A8, so I designed my own setup. It's low-profile and leaves plenty of clearance around the circular fan, a feature I really appreciate. ...I'm happy to...

This fits on the standard carriage to the left.x_offset = 46y_offset = 7z_offset = 0.7 OR 3.6 if upsidedown (depending on heat block used)

Come on! ...Just press the print button and let it go straight to the printer!

<p>This is a remix from <a href="https://www.thingiverse.com/thing:4751635">thingiverse.com/thing:4751635</a> by travelcamel!</p><p>- Added holes to secure the cover via the 2 screws<br>- Added a mirrored version to mount it on the right side</p>

Auto leveling arm for the ToAuto Pyramid A1.1 printer. The original one was too flexible so I made this one. ...This one is geometrically stronger and can be easily printed.

There is some one design the mount but it seem, i cannot adjust the height or routing the wiring properly, thus i have created this to mount on my Printer

Printed in ABS and glued with acetone to existing stock tool head carriage.

Base on this design: https://www.thingiverse.com/thing:4927021 I have some trouble using this model because bltouch too close to my bed, so it can drag print model. I move it up about z+ 1.5mm and from y- 1mm to make room for bltouch cable jack...