bit keeper 3d models

I mimicked a bit of adafruit's NeoPixel code to give the side spinners their trailing glow effect. I made sure to leave the intensity and speed settings as variables so I could quickly adjust them and get the effect just right. Several hours later, I...

For electronics, I used the information from this site https://alexgyver.ru/gyvermatrixbt/ and chose the simplest option. BOM (approximately $7) WS2812 LED Full Color Module 64 Bit 5050 RGB (approximately $ 4)...

I also modified the airtight spool holder mount to make the top opening a bit narrower, and add some corner braces at the bottom to make it stiffer. Enjoy!<br><br>EDIT March 10, 2022: I added a few parts for a filament runout sensor mount that pivots...

If you use the caps, apply a little bit of plastic glue/superglue… if you ever need to remove the door without using the magnetic lock, simply use a flat screwdriver and a little tap to remove the caps and after that the steel rod, thus releasing the...

-------------------------------------------------------------- Instructables link: https://www.instructables.com/DIY-Mini-UPS-for-WiFi-Router-V20/ Download the.STL file: Link will be available soon Download the Schematic: https://bit.ly/37mZ0i4...

AND YOU CAN ORIENT YOUR PLANTS AS YOU WANT, HOWEVER, THE SYSTEM WILL BE LOOSED A LITTLE BIT... THEREFORE ... WITH THE SYSTEM FULLY SECURED... USE THE DEFAZED DESIGNS PROVIDED. THOSE WITH 2 POTS - DEFAZED 90 DEGREE, WITH 3 POTS - DEFAZED 60 DEGREE, 4...

&nbsp;No glue is needed, as the parts fit tightly.4 - My apologies, but the teeth are a bit unwieldly to glue. &nbsp;After putting the mouth into the face and gluing the tongue in, do the teeth before gluing the face to the body. &nbsp;Be careful to...

All of the above along with unfinished cooling duct of the cyberfooks1 design caused me to decide to try my own skills to make a plate for Hemera for Tronxy X5SA Pro, addressing all above issues, adding a bit of rigidity and tuning everything to be...

I completed some basic programming to show the movement of Ninja:   https://youtube.com/shorts/zjgVOHkwsz4A bit of philosophy:  Often we build these projects and just insert code someone else wrote and hope the project works. This is not the nature...

Plus, fishing the small factory battery out of my pocket every time I needed to change it out was proving to be a bit annoying. Many FPV pilots mount their batteries on the strap of their goggles, but if I was going to use a bigger battery, I wanted...

&nbsp;&nbsp;Assembly is quite straight forward, and a little bit of patience in getting the size right will be rewarded with a very neat finish.SELECTING THE BOTTLEAny bottle will do, as long as it has a section with parallel sides that can be cut to...

The size is a bit smaller than the original one, since I wanted to print the arm of the stand (the most critical part of the design) in one piece. I am now very happy with the size of 31 cm x 19 cm x 39 cm and would not like it to be any larger. The...

This also makes it a bit shaky when you slide/move it. ...Remember: The system is not meant to be rock solid, but functional and clean looking.&nbsp;</li><li>To move the glider, simply pull it, change the position and push it back...

The mount for the Arduino Uno *may* be a bit tight, to fix this you could file the gap for the ports down, or physically file down the DC power Jack (I have found this port to cause the most pain), even then you may need to use a reasonable amount of...

You may find the Colorprint tool useful if your printer supports the M600 command, but your slicer doesn't support adding pauses: https://www.prusaprinters.org/color-print/After switching filament colors, the nozzle may not be primed and the first...

Magnets: Use a tiny bit of 2 part epoxy or equivalent to glue your 3mmx12mm round neodymium magnets into their slots. I HIGHLY recommend using some rubberised clear tape over the top of the platform after installing the magnets, and also a small...

**Fitting** --- All of these parts are designed to fit snugly over the extrusions and they work perfectly on my machine but they may very well be too tight on yours due to everyone's prints and extrusions being a bit different. **As a result, I...

Top view error: notice the non-concentricity in the center mounting hole Front view error: mine sticks out a bit further on the ends. Future improvements: lever I can only do so much, so I settled for producing a friction version. The rear shifter I...

I found my method a bit easier, but YMMV. The adjustable feet were tapped with M5 threads and move up and down overlong bolts installed in three locations under the ground board. One is long as it mounts direct to the extrusion bar, the others are...

This version requires a fair bit of sanding, but once sized correctly is the smoothest and most reliable, handling a little more force. However, this version results in much more resistance and essentially requires using a setscrew to attach...

FYI: Total depth inside the board grip part is 1.128" from the outer most surface so you will have quite a bit of travel for a bolt. Most thread lengths on the partial thread bolts are usually less than 1" and will not have to worry about bottoming...

My Ender 3 Pro and the upgrade board 32 bit board both needed to be re-calibrated from stock. 2. You may still need to use the initial layer horizontal expansion (Cura) in your slicer to manage any remaining elephants foot. 3. Flow rates for your...

Added a small rise to the lower/female lip to soften the sharp corner, and now including a PETG printer config that seems to produce good results. Update April 7, 2020: We've found that PLA seems to print a bit more air-tight than PETG, but that can...

It allows the full width of the Prusa MK3S hotbed to be used.Regarding the 1:50,000 scale print, quite a bit of resolution is gained, now the peaks or needles can be counted in tens and many characteristic features of the mountain can be...

(Otherwise, you can use insulated wire for this). This is a bit ugly – you can do better! I didn't have any fine pliers, so I just used flush cutters (very gently!) to bend the outer wire. If you're using insulated wire, just cut this to as short a...

Probe offset (on mine) is X -49.0 Y -8.4, but measure, and update your probe offset.2/3/24Updated the duct files, specifically the right side I tweaked quite a bit. Now I have really good centered air directly under the nozzle. Suggest if you printed...

I will be the first to admit that this version may be a bit over-engineered, but with 3D printing why not?Fishing line is strung between the pulleys and the ghost/s are attached using fishing swivels.As the pulleys rotate, driven by a motor, the...

Every box is a little bit different so it is the best to fix thr rear panel at the half-finished box (like at the photo) then glue in the rectangular parts and push them in the direction of the yellow arrows. Now we need the two D-shaped sliders and...

Update 9 (03.07.2018): After test driving the Z-Axis I saw, that the designed version of my bed brackets weren't stiff enough and bend quite a bit. Therefore I designed new bed brackets which are holding the bed really well now. Updated designs and...

If you want to use the hardware I intended this to use: Hinges Bolts- https://www.mcmaster.com/91292A018/ (you will need to thread inner most hinge) Hinge spacer- https://www.mcmaster.com/91755A311/ (you can see in the photos a little bit of white in...