biqu h2 3d models

This is a remix of the designs from: https://www.thingiverse.com/thing:4740250 https://www.thingiverse.com/thing:4966561 https://www.thingiverse.com/thing:4749419 I have updated the following: - Updated the components to work with the Biqu H2 V2 with...

(Update 10/2021: Added screw and made small adjustments) --------------------------------------------------------------------------------------------------------------- Hallo, ich habe versucht eine Gießform für den Phaetus Dragon Fly & Biqu H2...

### Mount Plate with modular FanDuct for Artillery Sidewinder X2 for BIQU H2 Direct Extruder **New V3** [See V3 on YouTube](https://youtu.be/KshpXn8GP5A) - FanDuct is modular, support all H2 Extruder variants and all Nozzels (V6, Revo,...

REV1: Fixed the BLTouch Fan bracket and Upper Bracket for issues Full details regarding development of this assembly can be found here: https://forum.v1engineering.com/t/mp3dp-v2-biqu-h2-direct-drive-hotend-combo-option/31340 MP3DP v2 Can be found...

Finally, remove the rubber stopper and slide the assembly all the way to your right and install the last two screw through the adapter and in to the BIQU H2 from behind. Now, you need to connect to the printer with a pc or through a raspberry pi and...

This is an adapter to run a linear rail on the X-Axis of your Ender 3/3 Pro coupled with a BIQU H2 direct drive extruder. The needed hardware is as follows:<br>10pcs M3x6mm button head screws<br>4pcs M3 T-nuts<br>There is no modification necessary to...

This is a mounting plate for the BIQU H2 on a Longer LK1/Alfawise U20 printer. You'll need to drill out the carrier plate on the LK1. The thread pattern doesn't match the BIQU extruder and causes all kinds of problems when mounting. Loosely fit the...

If you want the longer sides front and back, check out this remix: https://www.thingiverse.com/thing:4864920 Complete system to mount a BIQU H2 to a Crealty CR-10 V2 or V3. Route heater and thermistor wire between mount and plate. Heater wire should...

If you want the longer sides front and back, check out this remix: https://www.thingiverse.com/thing:4864920 Complete system to mount a BIQU H2 to a Crealty CR-10 V2 or V3. Route heater and thermistor wire between mount and plate. Heater wire...

This design allows you to mount a Biqu h2 direct drive extruder on the flsun Super Racer Bill of materials: 8mm m3 spheres: https://a.aliexpress.com/_mPCzgsS 65mm m3 rods: https://a.aliexpress.com/_mM0en9u 40mm fan: https://a.aliexpress.com/_mrzeFn2...

I designed the cable mount to be used with a mounting bracket that extends across the top (4mm bracket) but it can be modified as needed with the included STEP file.You will need the following screws:5x 8mm or 12mm M3 button head screws3x 20 mm M3...

A complete set of mounting kit for Biqu H2 (H2S may also work) extruder on Sovol SV04. This kit allows you to use factory 4020 fan instead of 5015 fan.This printer is a nightmare, it never worked no matter how I tried. It always having unexpected new...

This is a mount, compatible with the stock print carriage on the D-Bot, for a BIQU H2 hotend and extruder. It also includes a side-mount for a BLTouch probe, and a mounting location for an Adafruit LIS3DH Triple-Axis Accelerometer. For...

Note: as of now this does not have a place for the auto-level sensor since I'm using mine as a zstop currently, file added for that part as X5sa Zstop mount.stl This is a mount to fit the Biqu H2 direct drive extruder to the stock carriage plate of...

I reworked the bracket the mounts the fan duct and 5015 blower fan to the BIQU H2 direct drive extruder. The changes I've made are the following, due to the fan duct snagging on 3d prints. 1. Made fan mount adjustable from .5mm - 2.5mm 2. 3....

This is yet another parts cooling fan duct for a 5015 radial fan to mount to a BIQU H2 direct drive extruder. I'm calling it a remix of [looxonline's](https://www.thingiverse.com/looxonline) fan duct, although I didn't directly modify the original...

I've also made a slot along the bottom for it's cables to route through (you may also get the fan cable through there).I've also made room for an ADXL345 sensor on the top.&nbsp;My print settings using the BIQU H2:Nozzle temp: 240°cBed temp: 80°cNO...

This was done primarily for the Ender 5 Pro but will fit any BIQU H2 installation. This version gives 360 degrees of cooling. I've also remixed the mount so that its slotted for height adjustment and also off-set from the hot end so the heater...

https://www.thingiverse.com/thing:4893522 It uses the original part cooling fan from the Ender 3 (and I assume the Ender 6, since that is what the original used) and mounts to the side of the Biqu H2 for part cooling. On my ender 3, I was...

This fits the BIQU H2 extruder and uses a 5015 blower. I have it installed on an Ender 3 v1 but it should fit most printers with this extruder. I used zip ties to hold the fan on and also for the cable support. The cooling performance seems pretty...

If you are using Fusion 360 you should first edit the "Blower Entry" and "Blower Holes" sketches inside the Part Cooling Biqu H2 - 5020 component, and if you need more space to fix the blower edit the "Fan Hold Bottom" and "Fan Hold Top" to give you...

But it works great so far!I also added a guide for a reverse bowden setup (see the image)If you're curious about my cooling solution, it is this:(you need both) https://www.thingiverse.com/thing:4911219 https://www.thingiverse.com/thing:4042492After...

Das ist meine persönliche Version eines platzsparenden Bauteilkühlers für den Biqu H2 Extruder. Ich wollte ihn Einteilig haben, mit der Möglichkeit ihn variabel in der Höhe anzupassen, wenig Platz einzunehmen und leicht zu montieren. Es gibt hier...

*** This is a mod to mount a Biqu H2 direct drive extruder on an Ender 3 without losing print volume. Due to the larger width of the component compared to the stock hot end, you need to make a small modification to the Y axis to recover the lost...

This is a BIQU H2 Mount for the tronxy XY-2 Pro and a perfect fanduct based on the OmniaDrop from www.dropeffect.com. (thanks for the permission!) At the back of the H2 is a tunnel for the heater- and the thermistor-cable. At the edges are tunnel...

Крепление BIQU H2 4x4 для Ender-6 --------------------------------------------------- Целился получить максимальную площадью печати. Для этого сопло расположено по центру каретки. **Внимание**: чтобы получить 274 мм пролет по X, сначала необходимо...

This is a mounting plate for the BIQU H2 on a Longer LK1/Alfawise U20 printer. You'll need to drill out the carrier plate on the LK1. The thread pattern doesn't match the BIQU extruder and causes all kinds of problems when mounting. Loosely fit the...

This is a mount, compatible with the stock print carriage on the D-Bot, for a BIQU H2 hotend and extruder. It also includes a side-mount for a BLTouch probe, and a mounting location for an Adafruit LIS3DH Triple-Axis Accelerometer. For printers that...

This is a mount, compatible with the stock print carriage on the D-Bot, for a BIQU H2 hotend and extruder. It also includes a side-mount for a BLTouch probe, and a mounting location for an Adafruit LIS3DH Triple-Axis Accelerometer. For printers that...

An all in one BIQU H2 Extruder mount for an Ender 5 or five plus, X and Y end stop mounts are from from a linear rail upgrade kit. I've uploaded a couple remixes, of the Y enstop I think the V2 should be about right as the V1 was too Small Nozzle was...