biqu h2 v2s lite mount 3d models

This is a remix of the designs from: https://www.thingiverse.com/thing:4740250 https://www.thingiverse.com/thing:4966561 https://www.thingiverse.com/thing:4749419 I have updated the following: - Updated the components to work with the Biqu H2 V2 with...

This is a remix of the designs from: https://www.thingiverse.com/thing:4740250 https://www.thingiverse.com/thing:4966561 https://www.thingiverse.com/thing:4749419 I have updated the following: - Updated the components to work with the Biqu H2 V2 with...

This is a remix of the designs from: https://www.thingiverse.com/thing:4740250 https://www.thingiverse.com/thing:4966561 https://www.thingiverse.com/thing:4749419 I have updated the following: Updated the components to work with the Biqu H2 V2 with...

A remix of Lanfeust_dsn's excellent adaptor plate for attaching a BIQU H2 to an Ender 3 X carriage, but with the addition of a bl-touch mount stolen from 5teveO that does not interfere with my front mounted fan nor the manual extruder knob. This is...

My take at a front mount part cooling solution for the BIQU BX and H2 Extruder. Combined with the stock fan and running both in parallel you get 360° part cooling and much better overhang results. And just fyi, the stock fan plug is a JST-PH...

Note: as of now this does not have a place for the auto-level sensor since I'm using mine as a zstop currently, file added for that part as X5sa Zstop mount.stl This is a mount to fit the Biqu H2 direct drive extruder to the stock carriage plate of...

Mount for the BIQU H2 Direct Extruder for the Anycubic i3 Mega based on the [X-Carriage MK4](https://www.thingiverse.com/thing:3537449) from [@ML3DPrinting](https://www.thingiverse.com/ML3DPrinting). The included 24 V fan and heating cartridge...

Sunon EE4010S1-1000U)2x M3 nut [fan]6x M3 6 mm [4x main extruder mount, 2x bottom extruder mount]2x M3 10 mm [X-Carriage]3x M3 16 mm [2x fan, 1x bottom extruder mount]WARNINGIt may happen that the extruder bumps into the frame when moved to max...

A complete set of mounting kit for Biqu H2 (H2S may also work) extruder on Sovol SV04. This kit allows you to use factory 4020 fan instead of 5015 fan.This printer is a nightmare, it never worked no matter how I tried. It always having unexpected new...

This is a combination toolhead mount and remote part cooler for the BIQU H2 with Revo hotend and the Ender 5 Plus. It also incorporates a mount for the CR/BL touch which keeps the Y offset of the probe at zero. The remote cooling is supplied by a...

An all in one BIQU H2 Extruder mount for an Ender 5 or five plus, X and Y end stop mounts are from from a linear rail upgrade kit. I've uploaded a couple remixes, of the Y enstop I think the V2 should be about right as the V1 was too Small Nozzle was...

This is a mount, compatible with the stock print carriage on the D-Bot, for a BIQU H2 hotend and extruder. It also includes a side-mount for a BLTouch probe, and a mounting location for an Adafruit LIS3DH Triple-Axis Accelerometer. For printers that...

This is a mount, compatible with the stock print carriage on the D-Bot, for a BIQU H2 hotend and extruder. It also includes a side-mount for a BLTouch probe, and a mounting location for an Adafruit LIS3DH Triple-Axis Accelerometer. For printers that...

*** This is a mod to mount a Biqu H2 direct drive extruder on an Ender 3 without losing print volume. Due to the larger width of the component compared to the stock hot end, you need to make a small modification to the Y axis to recover the lost...

This design replaces the stock X carriage bracket of a Anet A8 / AM8.The backplate features a mounting pattern for a BIQU H2 V2.0 extruder / hotend, using 4 attachment screws. A second part features attachment points for a 5051 blower fan, an...

I have it mounted to a BIQU Hermit Crab system but the design should work on any printer if you print a custom back plate that fits your mounting holes. The goal of a cooling fan is not maximum air flow, it is the RIGHT amount of air flow. Since...

Finally, remove the rubber stopper and slide the assembly all the way to your right and install the last two screw through the adapter and in to the BIQU H2 from behind. Now, you need to connect to the printer with a pc or through a raspberry pi and...

This is an adapter to run a linear rail on the X-Axis of your Ender 3/3 Pro coupled with a BIQU H2 direct drive extruder. The needed hardware is as follows:<br>10pcs M3x6mm button head screws<br>4pcs M3 T-nuts<br>There is no modification necessary to...

https://www.thingiverse.com/thing:4893522 It uses the original part cooling fan from the Ender 3 (and I assume the Ender 6, since that is what the original used) and mounts to the side of the Biqu H2 for part cooling. On my ender 3, I was...

This was done primarily for the Ender 5 Pro but will fit any BIQU H2 installation. This version gives 360 degrees of cooling. I've also remixed the mount so that its slotted for height adjustment and also off-set from the hot end so the heater...

Mount for the Biqu H2 extruder on the Sapphire Plus (SP5), probably also would work on SP3.-Mounts on two points, to keep nozzle very firmly in place. One mount goes between the hotend fan and heat sink, the other around the extruder and integrates a...

* 2 - 2.5M nuts and cap screws for the adxl343 __if using__ **Note:** My initial print quality with the BIQU H2 was poor. I got in touch with the company and they recommended changing the retraction to 1mm and the retraction speed to 15mm/s. Both...

If you are using Fusion 360 you should first edit the "Blower Entry" and "Blower Holes" sketches inside the Part Cooling Biqu H2 - 5020 component, and if you need more space to fix the blower edit the "Fan Hold Bottom" and "Fan Hold Top" to give you...

This mount is only 5mm thick while still being rigid enough to handle relatively fast accelerations without too much wobble.&nbsp;The removeable fan mount makes the already hard to service H2 just a little bit easier and allows you to have two...

... no need to use the bottom 2 screws. Note: My initial print quality with the BIQU H2 was poor. I got in touch with the company and they recommended changing the retraction to 1mm and the retraction speed to 15mm/s. ...Both worked really well for me.

Lightweight, compact mount for h2 extruder on Ender 5 proDirect conversion to 4010 or 4020 fanuse the original screw to fix it and 2 m3 10mm for fixing the fan support only on the build plate cable relief:...

Lastly the fan ducting can be mounted (i am currently using this https://www.printables.com/it/model/267010-biqu-h2-v2v2s-fanduct-for-single-dual-5015-fan-sta ) along with the probe if you have it (some options for mounting are included).I printed it...

This was done primarily for the Ender 5 Pro but will fit any BIQU H2 installation. This version gives 360 degrees of cooling. I've also remixed the mount so that its slotted for height adjustment and also off-set from the hot end so the heater cable...

Here is a mounting and fan duct system for the BIQU H2 extruder. The mount includes routing and fastening points for the wires. I was able to center the nozzle in X to match the OEM Ender 3 nozzle. However, the Y has been offset around -25mm. To...

I made this mount because I had problems with my Biqu H2 V2 on other Mounts I found. The Bltouch was basically the same height as the nozzle when retracted and I wanted something with cable routing through the back. Maybe that has something to do...