biqu h2 part cooling fan 3d models

After using the fan mount and duct by eight_heads for a few days, I found that the fan duct was sometimes hitting the build deck and the printed parts. When it didn't hit, it was very, very close to the deck. In my situation it just wasn't going to...

Remix of lightninglord88 fan duct (https://www.thingiverse.com/thing:4816138) with the part than covers the manual feed gear removed (crudely) in maya. ...STL export broken for me so its an OBJ but should import fine.</p> <p>Cura was fusing the...

just what i came up with to solve everything that is did not like about the mount and to make it very strong. ...the fan

Modified version of thing 4682915. ...Screws can be adjusted to place the fan lower or higher than the standard height. ... Remix of https://www.thingiverse.com/thing:4682915.

This allows adjustability of the height of your duct without removing the fan. During printing, pause the print to drop 2 M3 nuts into the slots. I have included 2 versions. I have printed the rounded version with supports, but have included a...

This is a remix of the 5015 Fan duct and mount by eight_heads. This one raises the duct 3.5mm and moves it to the left 2.5mm in order to clear the heat block in a different rotation on the V2. ... I also removed the "BX" and replaced it with "CR10"...

I just cut the one tab off the fan shroud with side cutters for clearance, I used a short m3 or m4 screw that just threaded right in there, it isn't tight but fit well enough to hold everything in place Second is the endoscope mount. The original...

I just cut the one tab off the fan shroud with side cutters for clearance, I used a short m3 or m4 screw that just threaded right in there, it isn't tight but fit well enough to hold everything in place Second is the endoscope mount. The original...

The fan hole is sized to an 5015 blower fan.Print with brim to better adhension and for nicer holes.Min. perimeters 2Bottom solid min. 3Top solid min. 2Infill 10%Slower speed is recommended on small perimeters for better screw holes and make...

To enable me to do this I designed and printed a new fan duct for a 5015 Fan, mounting bracket and BLTouch spacer. Watch the video and then if interested buy a Volcano nozzle and print the new fan duct, bracket and BLTouch spacer (if fitted). ...

Mount, cooler and parts for the Biqu H2 direct extruder designed for the Biqu B1&nbsp;

biqu h2 cetus mk1/mk2/mk3 mount

... wire to be mounted and secured to prevent cables from twisting as much during printing. PARTS NEEDED m2x16 (x2), m3x8 (x4), m3x16 (x2) bolt and nuts m2 for the probe m3x8 for mounting biqu m3x8 for fan mount to biqu mount m3X16 for noctua fan

BIQU H2 Adapter für Ender 5 PLus und BLTouch

Model of outer geometry and dimensions of Biqu H2 extruder

Model of outer geometry and dimensions of Biqu H2 extruder

Biqu H2 ADXL345 mount Insert required for mount the ADXL

Mount / part cooler fan duct for 5015 Blower for Biqu B1, and Pin to hold the Blower in. Plenty far from the heat block - PLA can work fine. v2 - Reduced Height .75mm on the lower duct to keep it further from the build plate. ... Helpful for...

Just be sure to leave a link to the files in comments for everyone to enjoy =-P Ender 3 / Aquila H2 Mount X-Linear rail, BIQU H2, Bltouch, 50mm BlowerFan by Schwab_Manufacturing_Solutions October 04, 2021 https://www.thingiverse.com/thing:4982167 MAD...

... mount for the ADXL345 accelerometer. The Fan Mount is taken from https://www.thingiverse.com/thing:4816138 I will modify it soon UPDATE Sept. 9 2021 Changed the Breakout Board Mount to make it possible to use the original Biqu H2 Motor Screws

Cover for part cooling fan

It mounts to the fan mounting holes of the Biqu h2 Made for an 8 mm Endoscope. Uses an M3x10 screw to aim the endoscope and lock it in place. Uses the standard fan screws. I needed to file the inside a bit to make the endoscope fit tight. So...

There's not really a good way to use the filament release leaver on the Biqu H2. With this grip installed, now you can use it easily with a pinch! ...Use two M3 bolts to affix it to the top of the H2. Category: 3D Printer Parts

There's not really a good way to use the filament release leaver on the Biqu H2. With this grip installed, now you can use it easily with a pinch! Use two M3 bolts to affix it to the top of the H2. ... Category: 3D Printer Parts

I downloaded it and added my own backplate I have designed, smoothing out the iffy details and adding some extra parts.The goal for this carriage was to use a 4010 blower for part cooling, a SuperPINDA probe for ABL, and a 4020/10 fan for silent...

This is a very plain, very boring, very work-in-progress Rigidbot mount for the Biqu H2 extruder.

Simple cable guide for the BiQu H2 extruder I printed it in PETG on my Ender 5 Plus

Good adapter for the H2 direct drive on your Biqu B1 printer And BL-touch mount with cable holder

I remixed the E3d Titan Aero Eva mount to fit a Biqu H2 extruder . ... https://pkucmus.github.io/EVA/

Good adapter for the H2 direct drive on your Biqu B1 printer And BL-touch mount with cable holder