biqu h2 part cooling fan 3d models

This is an experiment. It does not have the best performance but it shows potential. ...Print using supports touching the build plate only.

The original design works well for the intended machine. However, when used with the BX the original design leaves the nozzle off center and the right side of the duct kissing the heater block. This small tweak simply repositions the duct so that...

This is a work in progress but it shows potential. ...Print using supports touching build plate.

The original design works well for the intended machine. However, when used with the BX the original design leaves the nozzle off center and the right side of the duct kissing the heater block. This small tweak simply repositions the duct so that...

Attach with double sided tape and power with external power adapter\r\n\r\n\r\n\r\n----- Rev.01 ------\r\nThis is the first iteration of a nozzle fan shroud I designed specifically for the Snapmaker.\r\n\r\nMore of a proof of concept at this point;...

Attach with double sided tape and power with external power adapter ----- Rev.01 ------ This is the first iteration of a nozzle fan shroud I made for the Snapmaker. More of a proof of concept at this point; was supposed to clip right on but the...

The fan duct attaches directly to the H2 so it will fit any printer that is running an H2 already, you will just need your own H2 mounting plate. All screw holes are the standard size that come on the ender and h2 however screw length may need to...

This is a fan duct mount for the CR-10S Pro V2 to use with the BIQU H2 extruder. I used the mount from here: https://www.thingiverse.com/thing:4799902 TLDR; I edited the Tiny Machines firmware to make the BIQU H2 work with CR-10S Pro V2. Follow...

... for other Geeetech 3D printers but I am not sure. Ofcourse you wont be able to mix colors if you choose this setup. Part cooling fan mount and bltouch mount are already available on thingiverse here: https://www.thingiverse.com/thing:4757657

This is a fixed version of the awesome fan mount for biqu b1 with H2. Because it was some error when slicing in prusaslicer/superslicer. ... https://www.thingiverse.com/thing:5022587

Added reinforcing to prevent snapping at the mounting ----- Remix of both BiQu H2 Fan duct (With manual filament gear exposed) by ar300500 on Thingiverse: https://www.thingiverse.com/thing:4822272 and BiQu H2 Fan duct with sensor mount and dust cover...

Remix of HelgeKeck's "BIQU H2 Chiron Mount" fan mount (which is a remix of lightninglord88's "BiQu H2 Fan duct with sensor mount and dust cover"). Both pages are linked in the sources. ... I added two slots to hold step down converter boxes from...

I have tried some Biqu H2 mounts and all of them failed getting wobble after short time use,I liked some designs so I have decided to mix them up in Blender,the result is a strong mount with no more wobbling problems.I have printed for 300 hours now...

This fan duct is designed to print without supports as orientated in the .3mf.This fan mount is intended to accompany the Biqu H2 bracket from here: https://www.printables.com/model/175642-twotrees-sapphire-plus-sp-5-v11-modular-biqu-h2-ex Using this...

I like the concept of the Modular BIQU H2 Mount for Ender 3.XBut I wanted to use my existing base mounting plate.The CR Toch was too close and the duct didn't fit.The original design is slimmed down so it can fit BIQU H2 Ender 3 V2 mounting...

A low profile adapter (5mm tall) for the BIQU H2 that lets you replace the 35mm heatsink fan with a 40mm one (4010 or 4020). This adapter is only really needed if you want to run a quieter fan or need more cooling if running very high nozzle...

I just recently added a biqu h2 to my ender 3 v2. I went through all the mounts out there and couldn't find a perfect single set of prints for my needs. This is a remix of the 3dfun mount I found somewhere, with the logo removed, and a tab added...

Inductive Z probe and Part Fan cooler for BIQH H2. ...I also started working on a duct for the part cooling fan but found I needed to run it at 50% and move it further away as is, so in my case, the duct was not useful.

I expect to change the ducts in the futureI like to park my printer a little outside of the hot bed so the filament has space to ooze while heating and I have enough space to clean the nozzlePrinted in PETG no supports required if you have the...

This is an end stop adjustment for the Biqu H2 direct drive extruder once mounted on the Biqu B1.This brings the nozzle ~3mm onto the bed surface. I will adjust it to bring it to as close to 0 as possible, but this got me up and running and wanted to...

This is a BIQU H2 mount for the Ender 5. It completely replaces the x-carriage plate. With this mount, you'll retain full range of the x-axis. However, like with all other mounts, you'll lose about 8mm on the y-axis. The usable printbed size will...

Ill probably redesign that holder to fit the MAD system at a later date.The original b1 holder has the biqu firebase usb-c pcb attached, and it includes the end-stop.This means i can cut the wires for heater, thermistor, fan to a few cm and run...

I used these fan ducts for part cooling: You can choose which you prefer. ... https://www.thingiverse.com/thing:4682915 https://www.thingiverse.com/thing:4757657 https://www.thingiverse.com/thing:4931226 https://www.thingiverse.com/thing:4915655 ...

X5SA Pro BIQU H2 v2 mounting plateyou will need 3 m3*h3 heat inserts and 2 m3x12 countersunk screws to mount this, works best with the fan mount, duct and bltouch mounts from here:https://www.thingiverse.com/thing:5202213

X5SA Pro BIQU H2 v2 mounting plate you will need 3 m3*h3 heat inserts and 2 m3x12 countersunk screws to mount this, works best with the fan mount, duct and bltouch mounts from here: https://www.thingiverse.com/thing:5202213

I just recently added a biqu h2 to my ender 3 v2. ...I went through all the mounts out there and couldn't find a perfect single set of prints for my needs.This is a remix of the 3dfun mount I found somewhere, with the logo removed, and a tab added to...

I just recently added a biqu h2 to my ender 3 v2. ...I went through all the mounts out there and couldn't find a perfect single set of prints for my needs.This is a remix of the 3dfun mount I found somewhere, with the logo removed, and a tab added to...

You will find the whole project to be able to mount the BIQU H2 V2S REVO on an X2 artillery.The assembly allows to put a BL_Touch (either a TOUCH_MI, or a BL touch)The assembly is planned for a 5015 blower.For the attachment on the cover, you will...

You will find the whole project to be able to mount the BIQU H2 V2S REVO on an X2 artillery.The assembly allows to put a BL_Touch (either a TOUCH_MI, or a BL touch)The assembly is planned for a 5015 blower.For the attachment on the cover, you will...

BiQu H2 carriage for MGN rail. ... Additional material needed: - 4pc DIN912 M3x10 - 4pc DIN912 M3x8 See picture for suggested print orientation.