biqu h2 mount 3d models

in order to be able to mount the biqu h2 v2 revo on my printer, i borrowed the base plate and adapted it to my needs. With my printer X5SA 330 Pro (2021) I lose some space due to the extruder. After the extruder is installed, the usable area is...

This is a mount for a BIQU H2 on my corexy conversion with MGN12H linear rails. I made for the Ender5Plus. The fan section has a mount that adds extra support from twisting and has the BLTouch mount directly on it. Make sure to use button head and...

Inspired by vampyrex13's BIQU H2 ABL mounts (https://www.thingiverse.com/thing:4893522).

Printed in ABS - remix of MK10 Linear Rail carriage to support BTT Biqu H2 For MGN12 Linear rails, with MGN12H block Mashed together in fusion with this - https://www.thingiverse.com/thing:4982167

mount adapter for bigtreeteck h2 v2s extruder on the ender 3

This is a remix of the designs from: https://www.thingiverse.com/thing:4740250 https://www.thingiverse.com/thing:4966561 https://www.thingiverse.com/thing:4749419 I have updated the following: Updated the components to work with the Biqu H2 V2 with...

This is a remix of the designs from: https://www.thingiverse.com/thing:4740250 https://www.thingiverse.com/thing:4966561 https://www.thingiverse.com/thing:4749419 I have updated the following: - Updated the components to work with the Biqu H2 V2 with...

This is a remix of the designs from: https://www.thingiverse.com/thing:4740250 https://www.thingiverse.com/thing:4966561 https://www.thingiverse.com/thing:4749419 I have updated the following: - Updated the components to work with the Biqu H2 V2 with...

Note: as of now this does not have a place for the auto-level sensor since I'm using mine as a zstop currently, file added for that part as X5sa Zstop mount.stl This is a mount to fit the Biqu H2 direct drive extruder to the stock carriage plate of...

A complete set of mounting kit for Biqu H2 (H2S may also work) extruder on Sovol SV04. This kit allows you to use factory 4020 fan instead of 5015 fan.This printer is a nightmare, it never worked no matter how I tried. It always having unexpected new...

This is a combination toolhead mount and remote part cooler for the BIQU H2 with Revo hotend and the Ender 5 Plus. It also incorporates a mount for the CR/BL touch which keeps the Y offset of the probe at zero. The remote cooling is supplied by a...

I made this mount because I had problems with my Biqu H2 V2 on other Mounts I found. The Bltouch was basically the same height as the nozzle when retracted and I wanted something with cable routing through the back. Maybe that has something to do...

It seems like BIQU changed the extruder hot end mounting bracket for the later models B1 printers. These have a full flat top section (as pictured). The nuts and bolts that hold the pulley wheels are much closer to the two mounting holes, which...

Weil ich einen H2 Extruder an meinem Projekt nutzen wollte und es keiner bis jetzt gemacht hatte, gibt es hier von mir einen Adapter, um diesen Extruder an der Voron 2.4 Aufnahme nutzen zu können. In meinem Projekt sind der X Achsen-Endschalter etwas...

It is an remix of user h19x51 model because with the original i had some little issues on my Genius Pro: too little space on the right side where the belt is connected to the base plate too little space on the lower left side where the base plate hex...

I made the mount to also fit my quick change system (coming soon) but you can also use it with 3 M3x8mm screws: You will also need 4 M3x16mm screws and 4 M3 nuts: I added A 5015 Fan Duct but you can use any one you want, use 2 M3x8mm screws: The...

Support for ender 3 max with BL-Touch.

This extruder is about 211 grams without the part cooling fan but with the extruder cooler. The respective parts on an M2 are about 248 grams. Ideally print in a stiff high-temp material such as car-fiber filled Nylon. ...PLA will not work.

Remixed it to fit Creality Touch form factor (connectors not located at the same position than BLTouch / 3D Touch)

Installation Notes ----------------------- • The BIQU H2 mounts on the top, bottom, and rear. Install all 4 screws loosely, starting with the top, then tighten them all. • Replace the two screws holding the hotend fan in place with (2) M3x16mm...

A simple basic mount for the Biqu H2 that fits the Anycubic Mega Zero 1.0 and 2.0, and a 5015 Hero Me Fan duct with BLTouch mount. == Credits to 3DE2016 for the Biqu H2 file: https://www.thingiverse.com/thing:4808811 Credits to TilTNimpuS for the...

Remix of HelgeKeck's "BIQU H2 Chiron Mount" fan mount (which is a remix of lightninglord88's "BiQu H2 Fan duct with sensor mount and dust cover"). Both pages are linked in the sources. ... I added two slots to hold step down converter boxes from...

This also brought my attention over to 2BK's (https://www.thingiverse.com/2BK) BIQU H2 mount for the above-mentioned MK4 X carriage. Since the overall dimensions of the BIQU H2 V1 which his design was based on somewhat matches my V2, I decided to use...

I have tried some Biqu H2 mounts and all of them failed getting wobble after short time use,I liked some designs so I have decided to mix them up in Blender,the result is a strong mount with no more wobbling problems.I have printed for 300 hours now...

   Feel free to support me, so I can create and share even more awesome projects. Thank you! Hello Friend! Come to my website. ...There you can find links and reviews about quality hobby products.https://MyHobbyTools.com ✔ 3D PRINTING My Favorite 3D...

Für weitere Infos bitte beim Original ohne Bltouch nachsehen. https://www.thingiverse.com/thing:4950260 Hier alle Stützen blocken ausser bei dem Überhang vom Bltouch. Mein Offset ist : X-2.00 Y-25.00 Z-1.75 mit einer Feder, die fest sitz. ... ...

There is an error in the drawing in the video. The correct drawing can be found at the links below, where you can also download 3D models of the project. https://www.infoconnector.ru/u... For better thermal conductivity, I lubricated the thermal...

for belt tensioner I remixed [this](https://www.thingiverse.com/thing:3730521) for fan duct I used [this](https://www.thingiverse.com/thing:4682915) Nozzle to probe offset is `#define NOZZLE_TO_PROBE_OFFSET { -34, 0, -0,22 }` Note: I used all...

you will need longer screws for the fan probe offset x50 y0 z-3.50

Liked both designs and thought I would share the combined project and save someone some time.