biqu h2 mount 3d models

A remix of 3D_LC's Biqu H2 Mount for the Ender 3, Ender3V2 & CR10. I have added a Biqu logo to each mount plate. ... BL-Touch offsets: Design 1: X58 Y~0 Z~2.7(need to calibrate for your printer) Design 2: X-40 Y~0 Z~2.7(need to calibrate for your...

Remix of the Biqu H2 Mount for Ender 3. On my Ender 3, the 2 holes to attach the mount to the original x axis plate did not line up, they were slightly out. I made one of the holes adjustable for those who may need it. ... You will need to ensure...

Hello, all the BIQU H2 mounts, that I saw so far, have been parallel to the rail. Due to the configuration of my printer and wanting to lose as little space as possible on the right and left, I needed a perpendicular mount to the rail. The design...

* Biqu H2 Mount * Moved mount holes away from base slightly to reduce mount strain and align better with the extruder * Redesigned bottom mount to increase space around hot end * Reduced mount from 2 holes to 1 hole to allow some room for cabling. ...

Ender 6 BIQU H2 Mount I was inspired by 3DPrintBeginner (https://www.thingiverse.com/thing:4822425) and their direct drive conversion of the Creality Ender 6 with the BIQU H2 compact extruder and hot end. However I also wanted to include a BLtouch...

Link to updated original model: https://www.printables.com/fr/model/186618-modular-biqu-h2-mount-for-single-or-double-5015-fa You can use other modules from original mount design as well (Except cable manager, I was too lazy to make a mount for it,...

This is a very plain, very boring, very work-in-progress Rigidbot mount for the Biqu H2 extruder.

This is my first work on fusion 360,it should work as a mount for a biqu H2 on the switchwire mod for the Ender3 that i'm working on

The original STL was too thick and didn't allow the H2 to reach the bed. This model has been replaced but the new model still has issues; it's a too tight between the x-axis rods. ...You can either force it, which is probably bad, or drill new...

BIQU H2 MOUNT WITH LINEAR RAIL & CR-touch SUPPORT

Anet A8 plus biqu h2 mount requires a few holes to be tapped to m3 for the X belt mount will also need some m3 nuts for the 2 outside 2 X belt mounts. lose around 6mm of travel with this extruder set up.. ... should work on most printers that are...

BIQU H2 mount with 2x4010 cooler fans for FlyingBear Ghost Works fine, running it for six months already, cooler blows ok I haven't calculated the printable area and there is no second cooler nozzle yet, mb I will draw it someday Mod I used to mount...

... metal plate. ...And/or were not easy to assemble.You will need 4 threaded m3 heat insert and some m3 screws.Note: I have no probe mount in this biqu h2 mount because I use a fanduct which has a BL-Touch mount (https://www.thingiverse.com/thing:5202213)

35mm Stock Fan BIQU H2 Mount wBLTouchI was really not happy with my previous design (https://www.printables.com/model/183260-ender-6-biqu-h2-mount) which was based on 3DPrintBeginner’s design. I wanted a compact, all-in-one, mount for the BIQU H2 and...

Ender 6 - BIQU H2 Mount with a 50x50 Hotendfan BLTouch supported For the part cooling fan a 5015 radial fan is required For the hotend fan i have used a 50x50x15 fan Maximum print area is 270x275 [stepper_x] position_endstop: 270 position_min: 0...

Ender 6 - BIQU H2 Mount with a 40x40 Hotendfan BLTouch supported For the part cooling fan a 5015 radial fan is required For the hotend fan a 40x40x10 fan can be used Maximum print area is 270x275 [stepper_x] position_endstop: 270 position_min: 0...

40mm Fan BIQU H2 Mount wBLTouchI was really not happy with my previous design (https://www.printables.com/model/183260-ender-6-biqu-h2-mount) which was based on 3DPrintBeginner’s design. I wanted a compact, all-in-one, mount for the BIQU H2 and...

Remix of the Biqu H2 Extruder mount for Ender 3/CR-10. The top right hand hole was in the wrong place for the wider Sunlu S8 carriage, so I moved it over 7mm. The rest of the design I left the same. ...

50mm Fan BIQU H2 Mount wBLTouchI was really not happy with my previous design (https://www.printables.com/model/183260-ender-6-biqu-h2-mount) which was based on 3DPrintBeginner’s design. I wanted a compact, all-in-one, mount for the BIQU H2 and...

Remix of @JLCURTIS excellent Biqu H2 mount, this time for the Ender 5 Pro. https://www.thingiverse.com/thing:4889163 This remix shifts the Biqu H2 by 13mm on the X axis to reclaim some print bed space. I've increased the BLTouch mount clearance as...

The cooling ducts and mounts I did not design they are The Modular Biqu H2 Mount for Single or Double 5015 Fan found at https://www.thingiverse.com/thing:5022551 and they are working pretty good. ... However I think that I'm going to try The...

... down that side of the original part. Stabilty of the Biqu H2 mounted using only one arm with two screws seems adequate. Mounting of this plate to the X carriage uses only two screws which also seems sufficient. It is ugly but functional. ...

Ender 6 BIQU H2 Mount*Update* I have a newer more compact version which can be found here (https://www.printables.com/model/183254-35mm-stock-fan-biqu-h2-mount-wbltouch).I was inspired by 3DPrintBeginner (https://www.thingiverse.com/thing:4822425)...

This is a remix of another outdated biqu h2 eva mount and needed to be modified for eva 2.4. many other files needed to be modified too to get the biqu to work so i labled them in the zip with a # (hashtag) sign at the end of each file name. The new...

Pros - Direct drive conversion - +10mm in X axis build volume (260mm total) - BLtouch mount - Accelerometer mount - Compact and clean - Good cable management - Very rigid Cons - -10mm in Y axis build volume (240mm total) - Have to remove H2 before...

Pros - Direct drive conversion - +10mm in X axis build volume (260mm total) - BLtouch mount - Accelerometer mount - Compact and clean - Good cable management - Very rigid Cons - -10mm in Y axis build volume (240mm total) - Have to remove H2 before...

Pros - Direct drive conversion - +10mm in X axis build volume (260mm total) - BLtouch mount - Accelerometer mount - Compact and clean - Good cable management - Very rigid Cons - -10mm in Y axis build volume (240mm total) - Have to remove H2 before...

Remix of @JLCURTIS excellent Biqu H2 mount, this time for the Ender 5 Pro.https://www.thingiverse.com/thing:4889163This remix shifts the Biqu H2 by 13mm on the X axis to reclaim some print bed space. I've increased the BLTouch mount clearance as it...

**work in Progress: I need to do an instruction with photography for mounting.** Biqu H2 Mount + cover for Bl-Touch for ender 3, ender3V2, CR10... It is a design that hide cables and have a nice finish. I will make an instruction to ount the...

Ender 6 BIQU H2 Mount ***Update*** I have a newer more compact version which can be found here (https://www.thingiverse.com/thing:5162948). I was inspired by 3DPrintBeginner (https://www.thingiverse.com/thing:4822425) and their direct drive...