biqu h2 extruder 3d models

This fits the BIQU H2 extruder and uses a 5015 blower. I have it installed on an Ender 3 v1 but it should fit most printers with this extruder. I used zip ties to hold the fan on and also for the cable support. The cooling performance seems pretty...

MakerGear M2 BIQU H2 V2 Extruder Mount and Klipper config file. ...Note that this will limit the X-axis to 188mm of usable space, and the Z to 185mm.

MakerGear M2 BIQU H2 V2 Extruder Mount and Klipper config file. ...Note that this will limit the X-axis to 188mm of usable space, and the Z to 185mm.

MakerGear M2 BIQU H2 V2 Extruder Mount and Klipper config file. ...Note that this will limit the X-axis to 188mm of usable space, and the Z to 185mm.I will probably change the part fan to be like the Ender 3 S1-Pro type.Category: 3D Printer Parts

Hi creators, I prepared a holder for a Bigtreetech H2 extruder for a Biqu B1 printers. As from other H2 holders, here you have a better access to the filament roller and hotend screws without disassembling fan. Also is this a more symmetric, where...

Removed mounting Bltouch mounting pad. ...I am using separate bltouch holder which is mouted to the holes on H2 V2S extruder.   See the link below. https://www.printables.com/model/727678-biqu-h2-v2s-bltouch-holder

Mount I made for the Biqu H2 direct drive extruder, it mounts using the 2 front holes, uses M3 hardware, and can be printed using any material. The mount needs some support but the fan duct doesn't need any. ... Hardware : -2 x 8mm M3 Bolts (Flat) ...

Remixed some thingiverse hemera mount for BIQU H@ extruder for my sapphire pro

A complete set of mounting kit for Biqu H2 (H2S may also work) extruder on Sovol SV04. This kit allows you to use factory 4020 fan instead of 5015 fan.This printer is a nightmare, it never worked no matter how I tried. It always having unexpected new...

I reworked the bracket the mounts the fan duct and 5015 blower fan to the BIQU H2 direct drive extruder. The changes I've made are the following, due to the fan duct snagging on 3d prints. 1. Made fan mount adjustable from .5mm - 2.5mm 2. 3....

Note: as of now this does not have a place for the auto-level sensor since I'm using mine as a zstop currently, file added for that part as X5sa Zstop mount.stl This is a mount to fit the Biqu H2 direct drive extruder to the stock carriage plate of...

The other mistake made by other H2 designers is to cover up access to the manual extruder thumb wheel. I use that wheel to prime new filament quickly. extrude a bit before each print, and to remove a filament when the day is over. I could not imagine...

This was done primarily for the Ender 5 Pro but will fit any BIQU H2 installation. This version gives 360 degrees of cooling. I've also remixed the mount so that its slotted for height adjustment and also off-set from the hot end so the heater...

So, I designed this mount for the H2 extruder a while ago, since there weren't many options around.It slots securely inside, guided by the two indexes that should easily make the stepper rest against them. The extruder body is fastened by three M3...

... Coming soon a part cooling duct for the 120mm fan... BIQU H2 - https://tinyurl.com/2p88seer BLTouch - https://tinyurl.com/mckn8c83 MGN12H 450mm - https://tinyurl.com/2s4d8jmb M3 screws kit - https://tinyurl.com/2p9xvz3c affiliate links above

This was done primarily for the Ender 5 Pro but will fit any BIQU H2 installation. This version gives 360 degrees of cooling. I've also remixed the mount so that its slotted for height adjustment and also off-set from the hot end so the heater cable...

If I would forget to change Cura's retractions, or was using a new slicer which uses standard 5-6mm @ 40+mm/s settings, I noticed that the small extruder on the H2 would actually get hot. This is not the case when using the recommended retractions...

  I did this because there are several versions of the h2 with different heat blocks and I couldn't find a bracket that worked with my v2 heat block.This is my process for dialing in the height:Secure the bracket screws just enough to prevent...

... with the cooling duct. Mount to the BIQU using M3x8 bolts. ...the boltholes here are a little tight at 2.8mm like corey designed them orinigally, i found you can simply turn the bolt and it will thread itself in so I didn't change anything there.

... original positions though. Fixes: - M4 (4.2mm) holes for fan + duct mounting - M4 (7.0mm) nut inserts - M3 (3.2mm) holes for extruder mounting This bracket is meant to be used with [Hangtight's fan duct](https://www.thingiverse.com/thing:4042492)

customized with 3D Slash!

After many adjustments there is a holder with wire transitions that includes what is needed, I printed in PTEG and the result is good

Support for ender 3 max with BL-Touch.

you can use the blank carriage plate with BIQU H2 extruder now. I have also included the part that will fit with the extruder to be connected with the plate. ..."E5+_H2_Mount_V5.5.stl"

Simple mounting, non-invasive part cooling duct for the Biqu H2 extruder using two 4010 Blower fans. Tolerances are quite tight, shouldn't need screws to mount the fans. Has been printed and tested. I recommend doing a water test once installed...

BIQU H2 V2 extruder mount for the Ender-3 printer. Quick-release https://www.thingiverse.com/thing:5124874 — very comfortable handle for unclamping the filament. ...Recommend.

Mount this extruder to the M2. ...Use a stuff high temp material, not PLA.

Complete 3D parasolid model of the Biqu H2 v2 extruder to develop your own ideas for your 3D printer. Attention, the interior details are not modeled for copyright reasons. ...It is exclusively a dimensionally identical image of the outer surfaces.

Please read this entire document before printing. Fancier looking BLtouch bracket that does not block airflow for the 5015 part cooling fan and mounts at the correct height instead of 1mm too high like the bracket this is remixed from. Tools...

Remixed the BL Touch mount to be compatible with the CR Touch