biqu b1 firmware 3d models

Managed to get 4 hours continuous use (350c / 5S in firmware) from a Makita 3AH 18v battery. ------------------------------------------- Battery Clips ------------------------------------------------------- Clips for battery should be printed at...

This took the longest time (hours) as every change I had to upload the new changed firmware moving only one point at a time to see what changed. Then I used the following codes most often to help in troubleshooting: G28 X0 Y0; Home X and Y only to...

Enter the pause settings for your printer, my CR10S Pro V2 stock firmware only works with the BQ M25 Method. Standby temperature should be set to your print temperature. * Select "Layer Number" in the "Pause at" dropdown * Set "Pause Layer" to 2 ...

This adapter is as simple as I can make it.Benefits compared to other optionsSimple to installNo firmware changes requiredNo structural compromises (it's attaches to the original metal assembly)The only downside is that it requires 3 x M3*8mm...

I changed my controller to an Einsy Rambo on my Ender 3's. Because i have changed to 16T Idlers and Pulley the steps/mm for the Y Axis need to be changed to100. I have checked the files and 20T Idlers could also be used so you you wouldn't have to...

Speaking of the X-Axis, you will need to modify the firmware to make the X-Axis 370mm to be safe. Because the stepper motor needs extra space than the original Bowden setup, you lose the width on the other side. It shifts the printable area of the...

Upload the “firmware”(which you can find on github here: https://github.com/fluetke/sandclock_fw)9.Solder wires from your dc-barrel-jack onto the RAW(+) and GND(-) pins of your arduino, then connect your Arduinos VCC, GND and the motor pins you...

- Easy access to SD card to easily flash the firmware (I never print from SD card). For the connectors, I've settled on GX avaiator connectors, the same used on the Creality CR-10 as they seemed to perfectly fit the bill. Here is a BOM to...

Fixes include:Update your firmware (to Marlin 2.0 if necessary) and change the settings to turn off power failure recovery mode, disallow the printer from writing to the SD card, and turn on arc calculation. ...(Also make sure your Printer Settings in...

Managed to get 4 hours continuous use (350c / 5S in firmware) from a Makita 3AH 18v battery. ------------------------------------------- Battery Clips ------------------------------------------------------- Clips for battery should be printed at...

... size). 2) Added an external USB-B port and relative on/off switch for being able to connect the printer to the computer in case I need to flash the firmware (used a 2-way USB-B switch). I'll post soon the relative files and photos. ... Enjoy!

You connect the Pi and the mainboard with a short USB cable externally, making it easy to connect a computer to the mainboard for firmware updates. There are also holes for inserting the various input/output connections to the board. On the left-hand...

* 2015-05-17 Customized Marlin Firmware Dan made a customized fork of Marlin to power the arm, initially tested on Atmega2560, which provided some bumpy results due to imprecise shape measurements. A calibration desk was designed for obtaining...

here is the video https://www.youtube.com/shorts/MsJpUYVWEn0 In order to understand the conversion of coordinate kinematics much easier, the provided firmware was used, it is a marlin 1.0.2. The files that must be modified are also attached. La...

Depending on the size of the washers used to level your print bed, it may be necessary to adjust the firmware end position (mainly in configuration.h) from #define Y_MAX_POS 100 to #define Y_MAX POS 98, to prevent contact between the bed and the back...

Our Y coordinates might not be the same (I am running the mriscoc professional firmware with some slightly modified bed dimensions), so I recommend investigating the Y positions yourself. This can be done by homing your printer and then adjusting the...

I prefer not to use the 50mm body and don't use the bracket part.\r\n\r\nCut down PTFE a few millimeters before the Bowden.\r\n(This part I will try to solve better with a modified body, so the bowden can be removed)\r\nPlace the new extruder and...

~$7Note, If needed for some reason the Pan servo can be assembled the other way around with a uni adaptor screwed to the bottom of the 90 deg geared mount so the servo is not rotating with the rest of the assembly and thus could be controlled from...

Aside from the Klipper firmware, everything else is a stock Longer LK4 Pro (basically an Ender 3, but with TMC 2208 in standalone mode and a color touch screen). Printing recommendationsNozzle: ≤0.4 mmLayer height: ≤0.3Spring material: PETG for...

(Most printers using the marlin firmware should be able to do this if they have it enabled. Tested on a Prusa i3 MK3S)</p> <p>I've added all the STLs I generated myself and all source material I used, except from the coaster with the Aperture Science...

Read on to the design section and I'll share a semi-secret that's holding you back if you've never monkeyed with the stock Anycubic firmware settings, too! Anywise. Also see the design section for all my reasoning that led to this design. You'll...

Reinstall any removed parts of Skelestruder, plug the IR cable into Einsy following Prusa's instructions, and change your firmware variant to MK3s. Rebuild, flash the printer, go to the support menu/sensors, and make sure IR is zero. Lift the idler...

I used a Teensy 2.0 and QMK for firmware. Because I installed the switches and soldered all of them before re-designing the plates, I needed to improvise to get the rigidity I wanted (hence the weird screws in the picture below). Here is my terrible...

At time of writing, I'm still running the stock firmware on my CR-10, so I cannot permanently update it on the controller. Instead, I added this line to my start G-code in my slicer: M92 E418; set steps per mm of extruder to 418. About the design:...

This has mainly been done through firmware/software updates. This is a hardware modification (that doesn't require any machine modification) that any 5th Generation Replicator user can print and install for themselves. Based on experience to date...

I've also included a layer cooling fan duct (you'll need to print two) that allows the use of your original cooling fans once you make the changes in your Repetier firmware. I used the original height and location from the 1.0 E3D mount I remixed,...

UPDATE: 12amp Afro ESCs (SimonK firmware) made a big improvement. UPDATE: I'm now running Lumenier 2206-11 motors and Gemfan 5x3 propellers. I added a KK2 flight controller (because I had an old one lying around). There are probably better options,...

This modification is to enable the full print volume of the Prusa i3 MK2.5,MK3, MK2.5S and MK3S when fitted with a Volcano heater block and nozzle without any firmware changes. Included in the modification are adjusters that fit between the...

This means there is no need to change ducts, or change the probe height or change Z off-set in printer firmware when swapping hot ends. 3. More Rigid. The extruders mount to the same monolithic piece of plastic as the hot end. In edition there...

1 x Vedder VESC V4.12 (Firmware updates and software can be obtained from VESC Project site) http://vedder.se/2015/01/vesc-open-source-esc/ https://vesc-project.com/...