biqu b1 dual z 3d models

... 3mm longer than what this mount was originally designed for). I just moved everything up by 3mm, now it fits. Z offset is -0.65 on my printer. ... Just tested this with an original BLTouch 3.1, and it seems to work fine with roughly -1.5mm offset.

Z offset is -0.65 on my printer. Just tested this with an original BLTouch 3.1, and it seems to work fine with roughly -1.5mm offset. Print Settings Printer Brand: Prusa Printer: Mk2.5sRafts: No Supports: NoResolution: 0.15 Infill: 20% Filament:...

WPL C14 Dual Motor Mount, specifically designed for N20 geared motors. ... This mount offers robust support for the popular WPL B1 and B24 series. ... Limited to personal use only; not intended for commercial applications.

A slight increase in height. So that the coil does not rub the roof. Size of enclosure is about 48cm x 58cm x 70cm(75cm) - if count distance between center of braces. +- 1cm Diameter of braces 8mm. Print * LEG x 2 without any modifications...

This is my holder for Sherpa mini extruder. ... Necessary parts: Screws: 2x M3x16 6x M3x12 1x Sherpa mini

Unscrew the 2 screws and remove white spacers from the filament sensor. ... Replace the spacers with new guide.

remixed, added space for screws for plate and removed sensor bmg mod is only for first test... ...looking for feedback what can be change

This mod is designed for canceling noise. You need to remove bottom bolt which is under the fan. You can assemble it with stock bolt. Enjoy! ... Use 10% infill 0.2 Layer hight 0.8 wall thickness

Designed to use a larger fan beneath the base of the printer ! Or, you know, just have a drawer. I removed the 3 fans from inside the base, cut a huge hole and wired a 140mm Arctic fan outside the base, so it needed to be rose. And here it is...

<p>I just prefer this over the paper method, simply because it delivers solid numbers I can write down and apply on all my printers with similar print surfaces. The gauge can be put in without tools (friction fit) and the preprogrammed 4-point bed...

Designed to use a larger fan beneath the base of the printer ! Or, you know, just have a drawer. I removed the 3 fans from inside the base, cut a huge hole and wired a 140mm Arctic fan outside the base, so it needed to be rose. And here it is : 4...

Just another fan duct based on the original one, Should be able to print without supports, gives better directional flow as it's not spurting it out the top like the original, and it is also much more open to allow for different heat blocks. ... ...

remixed, added space for screws for plate and removed sensor bmg mod is only for first test... ...looking for feedback what can be change

These foot are designed to provide greater stability and better control over printer leveling. Feet are threaded for height adjustment. Printing: Full print with 3x5x5 walls/top/bottom and 13% infil came to about 4x 22g in weight. ...

Created this based from https://www.thingiverse.com/thing:4946827 and image template from internet, maybe it can be useful for someone to do some measurement & design. ... FreeCAD & STP file format are included.

I added a new bimetal heatbreak from slice engineering that was longer and hit the old shroud. the focused air flow made a huge difference. ... I printed upside down with tree supports touching build plate only.

Designed for holding 10 UM2 Nozzles

I just prefer this over the paper method, simply because it delivers solid numbers I can write down and apply on all my printers with similar print surfaces. The gauge can be put in without tools (friction fit) and the preprogrammed 4-point bed...

Extra materials: - 6000RS bearing - 2 M3 screws and nuts My screws were too long so I used the washer provided. ... The T-nut I used wasn't made by me, I got it from here: https://www.thingiverse.com/thing:3050607

I got inspired but the guide from https://www.thingiverse.com/thing:4753681 but I don't have a after-market extruder. Remixed to fit the stock extruder. ... Features: - Fits stock extruder - Added room to maneuver the filament into extruder - Slots...

Helpful to prevent the spool to fall, and also when you are printing with a short piece of filament without a spool (see pics attached). I recommend you to print it with 100% infill, since it adds just a little in time and material but delivers a...

I made it cheap as possible and easy to install with uses stock extruder and stopper. ...Might required some longer bolt on gantry mount and stepper.

Das sind Filament Guide für links und rechts PTFE Kupplungen Das Gewinde M6 muss nachgeschnitten werden

Prueba de calibracion para la cama bed calibration test

Remix based from https://www.thingiverse.com/thing:4740855 & https://www.thingiverse.com/thing:4661251 Unscrew the 2 screws and remove white spacers from the filament sensor. ... Replace the spacers with new guide.

STL from btt

<p>When I changed the factory extruder by a BMG-like one which is bigger, the filament sensor did not fit. So I designed this simple adapter.</p><p>It´s needed tho small M3 screws to attach it to the printer in the former position of the sensor. ...Then...

I don't have a dual-color printer but I thought this would look cool if printed. You can re-scale it as low as 50% for a smaller print, but don't do lower on FDM. ...It is very difficult to print well at 50% scale, and it needs supports.

I don't have access to dual-color printing capabilities, so I was hoping this design would still be effective even if printed in single colors. ...You can easily scale down the model by as much as half for a smaller print, but be aware that attempting...

Remixed BIQU H2 5015 Cooling Duct by DTDakin (https://www.thingiverse.com/thing:5224768/files) STEPPER MOTOR CONNECTOR IS FACING UP, THEY COME LIKE THIS STOCK NOW BUT IF USING BIQU BX FLIP THE MOTOR AND ROUTE WIRE AROUND BRACKET OVER THE TOP NEXT TO...