biocube 3d models

Made this to contain the water flow from chamber one to the second chamber to flow directly into the filter floss i hade on top.with this no water escapes or dribbles past the filter floss.As far as i know this will fit the oceanic 8 gallon and the...

I created this skimmer specifically for my Biocube Reef Tank, and I'm excited to share it with everyone. This air-driven skimmer requires an air pump and a stone that fits inside the tube to effectively clean the water. I've been using it...

18mm OD Elbow designed for 30G Biocube.

Replacement hinges pins are required for the lid of the Oceanic Biocube 14 gallon aquarium.

Created for BioCube 16 compartment two. ... This part slides onto the top of compartment two so that the overflow from compartment one is redirected to the center of your media tray.

... water to flow further into compartment 2, permitting users to utilize more filter floss that is stored there. This device can also be used on an Oceanic Biocube by modifying the chamber wall between chambers A and 2 to create a smooth even surface.

Switch out bracket for Oceanic Biocube aquarium hood. Mine recently gave way and I was unable to find any suitable replacements online, so I turned to my trusty 3D printer. ...\r\n\r\nI've confirmed that this design works on the 14-gallon tank, but I'm...

I have the InTank media basket and just didn't see justification to pay for the refugium as well, so I designed one to fit the back of my Biocube 32. It allows me to grow macroalgae (cheato) with a light attached to the back glass. Holes are for flow...

This top filter tray is designed for use in the middle compartment of an older Oceanic 14g Biocube aquarium system. I am unsure if it will be compatible with newer models, so please let me know if you are able to verify this information. ... The new...

I designed a custom solution specifically for my 32-gallon Biocube aquarium, as I was frustrated with the existing options that compromised on durability and connection strength. What finally worked for me is this design, which fits seamlessly into...

This is something I made for my Biocube 32 Gallon aquarium. ...I got tired of looking for something that would fit and where the connections were actually strong and not fall from just touching them.</p> <p>This is what worked for me and it fits my tank...

bioball - biocube aquarium filter media space for benefical bacterium to grow

The Biocube remix fits in the center front of the aquarium and is positioned below the feed door. It allows the hood to be closed completely. The file has some manifold errors but will still print just fine through Cura. I don't have the time or the...

The Biocube remix fits in the center front of the aquarium and is positioned below the feed door. It allows the hood to be closed completely. The file has some manifold errors but will still print just fine through Cura. I don't have the time or...

The Biocube 32 aquarium has a solid connection for the return hose. While doing maintenance I broke the hose connection and did not have a way to connect the return line. These two models fit the hold in chamber 3 if you break your connection like I...

My Corlife Biocube 32 with upgraded Steve's LEDs was getting too hot and after removing the feeding lid, still would reach 82-83 degrees. I decided to create an 80mm fan mount that replaces the lid as the other fan options I saw ran from the back...

To ensure uninterrupted feeding for my fish during my vacation, I created a solution since the Everyday Fish Feeder by Eheim didn't fit perfectly on my BioCube 29's design. ...By attaching it to the front lid, which can be slightly raised, this makes...

I wanted a better use for the lid at the front of my BioCube, also needed a place for my automatic feeder. After making this part you can cut a plastic cup to act as a Ring to keep the dispensed food from getting caught in the current by the...

Created for BioCube 16 compartment one. This part snaps into the top of compartment one to hold a heater and temperature sensor. Made for: - 50W Eheim Jager TruTemp Aquarium Heater (Petsmart/Amazon/other) - Inkbird ITC-308 Digital...

Move all cable to one of the two Cable Holes on the rear of the Biocube 32 Mount fan on Bracket and then place bracket into one of the cable ports on the hood of your biocube 32. It should easily snap into place. Make sure the wording faces UP. This...

This is a bracket to securely hold a 40mm fan on the rear cable opening of a Biocube 32 aquarium. It will provide air current to cool the aquarium and maintain optimal temps. While most 40mm fans may work, I have only tested (and designed) it to be...

I got sick of how dirty my mom's biocube 29 was getting with the standard in tank media holder. I have to come over and do tank maintenance constantly. Floss just was't cutting it. So I designed this to hold the 2.75" Waterbox filter socks. Should...

I couldn't bring myself to pay for the refugium after shelling out for the InTank Media Basket, so I designed one. If you rotate the model you will see that I left one side open to mount a grow light on the back wall of the aquarium. ...This model was...

I purchased an Intank media basket, but the water director it came with had a significant gap - about 4-5mm on each edge - which allowed too much water to bypass the director and miss the media basket altogether. ...To solve this problem, I designed my...

Filter housing

I've noticed some of my freshwater neon tetras have been vanishing into the filter area of my aquarium. To solve this issue, I designed and created screens that securely attach to the existing inflow screens using simple clamps, effectively...

Cover your filter to block fish from swimming in dimensions 121mm x 96mm x 16.2mm

Up to 8 inches of float switch depth. Two float switches, one upper and one lower, ensure failsafe operation. Multiple positioning holes provide flexibility in installation. Works seamlessly with both NO and NC switches. Instructions I...

In progress (beta version 4), this project aims to have students study diverse environments using "One Cubic Foot" cubes and broken arrow shafts, inspired by David Liittschwager's work featured on National Geographic. The Ross School Innovation Lab...

Customized Version of Thingiverse Project ID: 253081 Generated with Customizer Tool from Thingiverse.com/Apps/Customizer/Run?Thing_ID=253081 Getting Started Utilizing the Following Settings: Cylinder Radius Size: 13 Units Cylinder Height Size:...