billy from hocus pocus 3d models

Belt tension limits for the left side, as its measured there.&nbsp;The maintenance values are from the 2022 FX/FXS/FXE manual. <a href="https://www.zeromotorcycles.com/en-gb/owner-resources">Please check</a> if they are valid for your...

I recommend letting Hugin pick the render resolution and then cropping and (down) scaling to the appropriate square image: stitching four 6000x4000 images from my NEX-7 nominally produces a 7648x7648 result (approximately 30x30mm at camera native...

It is easiest if you start with the chain hanging down from the handle. Start spinning slowly, and then start to vary speed, and even reverse the direction. Speed changes should be gentle, because abrupt changes will cause the chain to jam and fly...

On the other hand, it is necessary to remove supports.&nbsp;&nbsp;Print the following files:- Jupiter Vat Latch&nbsp;-Jupiter Vat Latch Base (left-rigth)You need (the pieces are only representations, do not buy these if you do not want):-Screw...

I've fitted my small hinges incorrectly! Fear not, there may still be a solution. If your small hinges seem to restrict your mask from opening, try printing out one of the "ShortArmV2" hinges. ...Replace one or both of your small arms with this and this...

You can make the product on a 3D printer or cnc machine from plastic, glass, steel, clay and any materials. the model can also be made using cnc machine turning wood.Also the model can be executions in castings. If necessary, I can make injection...

In marlin you need to find what you need uncomand it and compile and flash the firmware, in klipper you simply copy and paste few lines from the documentation and save it.Input shaping. The best feature of the klipper. it compensate the vibrations of...

An exemplar of woven wire container designed for Customer Service Representatives (CSR) A specific type of wire-constructed basket intended to cater to the needs of Client Support Representatives (CSR) A unique variety of woven wire receptacle...

I created slope from the base of the tray to the lip of the tray so the cubes slide out more easily than the original design. The slots for the Blue and Green cubes are slightly wider than the other slots. These wider slots will fit 7 cubes side by...

Also, changing the filament was a challenge with the height of the printer when it is placed on a table or plate. Destination: The filament spool should be placed at the bottom to make it easier to change and not have the weight of the spool on top....

Update 08.01.2022: Added some examples for test patterns included in this model.Update 12.01.2022: Updated presliced gcode to make sure heatbed is turned on.Update 18.01.2022: Uploaded additional stl with text on test patterns describing its...

You can make the product on a 3D printer or cnc machine from plastic, glass, clay, bronze and any materials. the model can also be made using cnc machine turning wood.Also the model can be executions in castings. If necessary, I can make injection...

If it causes copyright issues, i will remove it. Remixed from: https://www.thingiverse.com/thing:4248444 https://www.thingiverse.com/thing:4614658 https://www.thingiverse.com/thing:2506910 https://www.thingiverse.com/thing:3853037...

21,000 Lumen output from 150 watts10. Dimmable via 0-10 Voltage DimmingSuperior LED Benefits1. 60,000 hour lifespan.2. Can SAVE 50% or more on energy.3. Qualifies retrofit projects for financial incentives, including utility rebates, tax credits and...

So I can consider this bay as successfully working. Print instructionsI designed this with beginners in mind. I remember how terrible it is to have to remove each support from several pieces, and then discover that they don't fit together because my...

Don't tighten them yet.Insert this assembly from the top into the left side of the left Z-extrusion of your V0.1. Ensure that the wire goes to the bottom end of the extrusion (tips: You can cut off the standard Dupont connector to help you get the...

... Mark 5 of the part. I used a bunch of people in my office as beta testers. The beveling is from a suggestion, and a lot of attempts were made to hold the part to a phone so it can be used one handed but none of it was universal enough for my liking.

... All at OnceSurface Mode: NormalExperimental Extra Skin Wall Count: 0Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

But as I'm not a very experienced acrobatic pilot, I didn't try out more, yet.If you decide to build the model, I would appreciate a short report on your experience in the comments or you can contact me via the prusaprinter messenger.This would help...

supports R1 SP-SA Profile)6.25U Spacebars w/ a Centered Stem &amp; max height of 13.60 mm&nbsp;Print SettingsInfill: 15-20% GyroidPerimeters: 2-3Layer height: 0.2mmSeam: Rear or Near (check the preview in your slicer to see what looks...

Then, remove any excess glue from the top of the magnets to ensure the lid fits tightly, using an X-acto knife, screwdriver, spudger, or whatever you have.Tools that may help:If you print the holes slightly small, a 6mm reamer and a 6mm end mill can...

The love handles did not fit at all at first but I subtracted a few parts from them and now they slide right in, just be very careful when removing supports. The first torso pieces had some rough keys so I brought them back into meshmixer and...

I also made an exploded view drawing to help with assembly.Build can also be found on Thingiverse.Purchase Parts:QTY 12 - 20x6x2mm magnets (used to secure the doors from unwanted sliding and opening)QTY 8 - 6x50mm wood screws (used to mount the...

Like… very-nearly-the-whole-MK3s-build-plate-big, so don't be surprisedSettings (how I printed mine, at least):Prusa Slate Silver PETG0.4mm nozzle.2 layer height20% infill (resulted in some surface scarring, but it's not visible on mine when in...

;-) Hopefully you can figure out the orientation that things need to be glued in and where things go from the pictures. I know, I'm not much help with that am I? Think of it as the gauntlet is laid down and a super fun challenge in 3d spatial...

*I used brims on: windshield front_hub_bolts front_glow_red back_glow_red axles 5 - The windshield prints well, however depending on your slicer settings/filament/printer, one edge may suffer from overextrusion. If this happens on your print, do not...

The following example of a simple code to get you started: ```Python # Python code to create G-code with specific parameters and tool settings import math # Tool settings (parameters should be adjusted according to actual tools used) tool_diameter =...

Pneumatic Push-in Fitting Removal Tool This is a tool for removing the standard push-in fittings from pneumatic equipment. Made for both 4mm and 6mm tubes. I couldn't find any already-made tool models for this job, so I thought I will make my...

It links up to another spur gear (which I'm calling the auxiliary gear) to “grab” the rope and keep it from slipping.planetary gears:ring-gear.stlplanet-gear.stl (x3)sun-gear.stlrope spur gears (and related mounts):carrier-gear.stlcarrier-shaft.stl...

ESP32 DevKitC (v1 or v4 tested)...