bicycle cable holder 3d models

Cable holders for bicycle brake/gear cables.

Hello! ... This is cable holder that i designed for my Commencal Absolut Dirt Jumper frame. I'm sure it fits many other frames too. I printed it out of Pla Plus. Good luck! ...Please add pictures.

I finally managed to get my hands on a new brake cable, and it was a huge relief to have it up and running again.

Cyclist's trusted companion, the Montague bicycle, requires a reliable wire cable holder to keep its gear in check.

This is a customizable shift cable holder designed specifically for gravel bikes with 31.8mm frames. To accommodate different frame sizes, you can easily adjust the holder's fit by swapping out the M4 nut and screw provided. ...I fabricated this part...

Clips specifically designed to secure your brake line to traditional-shaped frame rails.

Securely attach a linear rail from OpenBuilds by hammering it firmly into position, then thread a bicycle brake cable through the corresponding hole in a parallel rail. ...Complete the setup by crimping the cable securely and allowing your drag chain to...

The teardrop-shaped top tube posed a challenge, so I created this cable holder that slides over the tube with ease. It securely holds the cable in place as the clip snaps into position. I printed these holders in black and used three on my bike -...

The original Fatty bicycle cable holder on my bike broke, so I opted for a DIY solution by creating a hex nut-style cable holder. This functional replacement not only fulfills its purpose but also allows for customization of your bike's appearance...

Bicycle brake cable clamp for 37mm front fork diameter (SR Suntour MG91) and 5mm cable diameter.

Bicycle cable clip for one hydraulic hose and a standard shifter cable. ...Designed for PLA

Used where bicycle cables (brakes/shifters) enter the bike frame for internally routed cables. Uses smaller diameter cable, so might not fit some brake cables. ... PETG seems to work well.

Replacement cable adjuster for bicycle brakes. Sample stl file is for 5/16 inch thread at 20 threads per inch and a 1/4" shielded cable. ... Code parameters can be set for any thread and cable size.

Cyclists often install adapters to upgrade their bicycles' cables, typically from standard 7mm outer diameter to smaller diameters like 4.5 or 6mm.

Cable stop with zip tie mounts for a bicycle shifter.Needed it for a geared hub so here we are.DO NOT USE THIS FOR BRAKES

Mount a sturdy clip to your bicycle frame by firmly securing it with heavy-duty double-sided tape, and lock a zip tie snugly around any cables you need to route, anchoring them safely in the clip's strong grasp. For larger-than-usual cable routing...

Design a reusable fastener for bicycle brake and shift cables in Sketchup, inspired by Shimano's cable housing clips. After multiple attempts, created a secure and rigid fastener that snaps onto both the cable and the frame's cable housing fittings.

I've been plagued by a nagging problem - my bicycle lights' tiny plugs that secure the cables had vanished. Determined to find a solution, I took matters into my own hands and conjured up a custom fix. ...The result is nothing short of brilliant - it...

This reusable fastener was designed by me in Sketchup specifically to secure a bicycle's brake and shift cables to the frame's cable housing fittings. Most people use small zip-ties when securing their bicycle's brake and shift cables to the frame.

Those days I was on a mission to devise an effective way to secure the gearing and braking cables on my custom-built bicycle. After some trial and error, I stumbled upon a solution that's commonly used in various industries for the same task - and...

A cable clip/holder/guide for a Giant Altra Vision Hybride They're not an exact match, but they do the job :).

Another use for this brake splitter is for running a single lever on a bicycle, say a track bike with one, seatpost brake lever, or as a disability aid for a partial amputee who still rides a bicycle. In this case, trim the 2 brakes so that the...

Compact Bike Cable Organizer Housing Clamp

A portion of a cable is visible, attached to its corresponding headpiece. ...The depicted component showcases the connection between the cable and the head, implying its functionality in transmitting signals or power.

Made these to plug up the empty internal cable routing ports on my bike after installing an AXS derailleur.

Simply slit one open along its spiral curve, then wrap it snugly around the cable. This DIY solution is specifically designed for use with 4mm and 5mm bowden cables. ...Keep in mind that you'll need to use flex filament to create these protective wraps.

... contains the design fitting 5-to-5 mm hydraulic brake hoses. ... The "4.2mm" file contains the design fitting 4.2-to-4.2 mm gear/brake cables. The "5mm_4.2mm" file contains the design fitting 5 mm (hydraulic brake hoses)-to-4.2 mm (gear/brake cables).

Braze-on Cable Guide by T70E turns out to be too thick and not flexible enough, so I've modified it a bit. ... Designed in DesignSpark Mechanical, I've attached the design file (.rsdoc) for easy modification.

Its a little standoff for Brake and shifter Cable at the rear swing to prevent excessive rubbing,photo shows Version 2 this is optimized.Version 4: Sizes in 13 - 17 mm width includedPrint instructionsPrint with brim at the flat side arrow up.

Bicycle - Left brake handle (cable)