bh1750 3d models

BH1750 sensor made from blueprints from datasheet

BH1750 light meter I2C module for your own DIY-projects! ...Special thanks:PCB 3D Models for 0603 SMD capacitorTony_Red for PLS-5 connectorEgor Chugay for SOT-23 packageVlad Mazur for 0603 SMD resistor

This is a simple BH1750 Case, to use with a 4Pin conector

this design is a holder of BH1750 sensor and ready to print on 3d print.

Case for BH1750 lightmeter sensor to attach to the Flipper Zero For wiring and installation refer to https://github.com/oleksiikutuzov/flipperzero-lightmeter

Montage eines BME280 und BH1750 für die Aluminium-Double-Waagen-Konstruktion eines beeloggers. Das transparente PETG, Füllgrad 30%, erzeugt ein Offset von etwa 12%. Ich habe den Code nicht angepasst, aber bei bedarf kann mir 3 Zeilen immer der...

Halter for the BH1750 Light Sensor. This was used in the weatherman-wetterstation setup. The variants with Faze and Breakthroughs are supposed to help when sticking the Halter onto a surface. I'm still using the version without Faze or Perforation.

The include .3mf file fits an Adafruit BH1750 (light sensor board) snugly and has holes for the pin wires.  This design doesn't have the STEMMA QT/Qwiic connection accessible, as my current project cannot use it, but allows for soldering to the...

Simple Mount for BH1750 Light Sensor Breakout Board Found on eBay for under $2, this mount is a bargain. It includes a socket that fits a 12mm diameter bubble level perfectly. To level it up, use M4 screws - you'll need an M4 tap to get started. If...

This compact box allows you to securely attach a BH1750 sensor to the back of a Raspberry Pi touchscreen case (or any surface that can accommodate a hot glue application). The hole is cleverly designed to conceal the connector cables from view. If...

Outdoor housing for the BH1750 sensor. I use this with a D1 mini to report light levels back to Home Assistant and automate some garden lights. I printed the base in ASA and the dome in PLA as I don't have white ASA. However, I would recommend...

My first contribution to this fantastic community. ... Find the small glass dome at your nearby hobby store or online at www (outer diameter 20 mm). Give it a quick sanding job so the light spreads out evenly across the luminance sensor of the BH1750.

Original project: https://www.printables.com/es/model/189821-d1mini-sensor-case-dht22-bh1750 I Modified the project to be able to store a LD2410C instead of the temp sensor. Also i opened part of the top case for the light sensor, as the...

It uses a d1mini flashed with Tasmota and a DHT22 and BH1750 (GY-302) as sensors. The data is published via MQTT to my HomeAssistant instance. This is a realy tight fit construction, so no need for glue. The electronics have to be pressed into...

This is my first attemp for a sensor case, which reads temperature, humidity and lux. It uses a d1mini flashed with Tasmota and a DHT22 and BH1750 (GY-302) as sensors. The data is published via MQTT to my HomeAssistant instance.</p> <p>This is a...

A revised version of the BH1750 holder, courtesy of pkscout, allows for easy attachment to a 27mm wide kitchen cabinet end panel using a clip.

BlackB0x grow monitor casing made for ESP8266, DHT22, and BH1750 - The bottom part is made to host ESP8266 without screws, just place the board and it will hold. The top part has a circle in the middle to host the BH1750 Light Dome, no screws are...

To house a BH1750 light-sensing circuit board, use transparent acrylic as a viewing pane. ...It might be necessary to expand the outer casing to 105 percent of its original size in order for it to fit snugly over...

This little housing for the light sensor BH1750 on a PCB is designed with simplicity and robustness in mind. The walls are chosen to be 2.6mm thick, and infill should be at 100%. The PCB features a multi-pin connector on its back and two mounting...

BH1750FVI is an digital Ambient Light Sensor IC for I2C bus interface. This IC is the most suitable to obtain the ambient light data for adjusting LCD and Keypad backlight power of Mobile phone. It is possible to detect wide range at High resolution....

Lighting The Path To Clarity: High-Sensitivity Intensity Measurement Module.

Check out http://solidworksavanzado.blogspot.com to discover advanced SolidWorks tips and tricks! This blog is dedicated to providing in-depth information for experienced SolidWorks users, helping them enhance their skills and boost productivity.

You're looking for a lightweight sensor holder that's easy to print and provides a snug fit for your header pins. To take it to the next level, consider adding some silicone details to seal out the elements and make it perfect for outdoor use. ...Simply...

This is a remix of https://www.thingiverse.com/thing:4575686 I just needed the BH1750 sensor in my setup so I modified the case to suit my needs. Adjustments made: 1. Closed the big opening for the DHT22 sensor. 2. Moved the hole for the BH1750...

This is a simple box for housing an ESP32 devkit v1 and DHT22 (temperature/humidity), BH1750 (lux) and LD2410 (presence) sensors.The box is oversized to keep the DHT22 the heat generated by the ESP32 and the LD2410 away from the DHT22.You will need 3...

I upgraded the standard enclosure to accommodate an rf-nano, a BH1750 light sensor and a BMP180 pressure/temperature sensor, resulting in a sleek, compact and well-designed package for my mySensors network at home. ... It links seamlessly to Domoticz,...

When I built a light sensor with a BH1750 I figured where to put the sensor, and the best place for me was right on top the case. ...Unfortunately it now needs supports to be printed, I highly advise to use the support settings from here:...

I needed a case for my nice illumination sensor BH1750FVI with a D1 Mini so I built this little case. ... I've printed it with PETG, 35% infill Light sensor: https://www.ebay.de/itm/233982638433?hash=item367a73b961:g:D5QAAOSwTWFghaK5 D1 Mini: ...

Enclosure for Two Motion Sensors HC-SR501, a DHT22 Sensor, and a BH1750 Connected to a Wemos D1 Mini.