bestway pool vacuum hose adapter 3d models

When you want to use your vacuum cleaner, just unscrew the filter cap in the swimming pool, and plug the connector on the pipe that goes to the pool filter. Of course, you will need a power enough filter (sand filter) This is a version for BestWay...

When you're ready to use your vacuum cleaner, simply unscrew the filter cap on the swimming pool and plug the connector into the pipe that leads directly to the pool filter. You'll need a strong enough filter, such as a sand filter, to ensure...

To use this adapter, simply insert it into the standard Intex pool skimmer hose attachment. Next, attach your vacuum hose to the larger end of the adapter. I printed this adapter at 50% fill and slowed down the print speed to ensure a smooth finish....

I designed a replacement adapter for my pool hose after discovering that the original had degraded and was flaking apart. They didn't fit well on my vacuum either, which prompted me to take action. I printed this new adapter in PLA plastic,...

A simple adapter to connect two 32mm / 1.25" pool hoses.That's it that's all..

Remixed from the Bestway cap and garden hose adapter, I modeled the plug as close to what I saw on Amazon. It took about a day and a half to drain my pool. The cap does not need supports, but the inside part does. Use thicker walls or 100%...

I was searching for a component that would allow me to attach a 32mm tube to the stock vacuum element of my Bestway pool, enabling me to create an underwater vacuum system for cleaning the floor effectively. ...Unfortunately, I couldn't utilize the...

This is a 32mm hose adapter specifically designed to be used with the Flowclear pool pump system.

Bestway Pool - Schlauchstütze. Das nachträgliche Einhängen funktioniert nicht so optimal wie gedacht. Eben den Schlauch kurz abziehen macht es dennoch möglich. Das Druckbett wurde fast aufs Maximum ausgereizt. Die Schlitze sind Materialersparnis,...

I needed to clean my bestway pool, but I wasn't crazy about using the garden hose method. So I started searching online and stumbled upon an amazing nozzle on Thingiverse https://www.thingiverse.com/thing:224431.\r\nTo make it work with my existing...

This adapter allows you to quickly swap out your automatic pool cleaner for a vacuum head with rollers, if you need to manually clean areas the automatic cleaner doesn't reach like the stairs. Both ends have a slight taper, so it should be a good fit...

To attach the 32mm hose from a pool vacuum cleaner to the water outlet fitting, which connects to the pump, follow these steps. We tested this method using an Intex pool and its accompanying pump. ... The inner threaded end of the hose screws directly...

Simply screw the adapter onto the wall fitting, then slide a standard 1.5" vacuum hose into place. The adapter works beautifully with fine debris, but may require manual intervention when dealing with larger items like leaves or sticks. If you plan...

As you can use only the propietary Poolhoses from Bestway and i wanted to use normal Poolhoses, I designed my own ones at 38 and 32 mm. I´ve also included the Ring to screw them onto the Pump In-and-Outlets. ... I´ve printed mine in PETG at 100 %...

This is a pump hose adapter designed to transition from the interior of a 32mm hose connected to the pool/pump to a 16mm outside diameter garden hose. If the garden hose fails to remain in place, gently push it further into the adapter and then...

This is a pump hose adapter to go from the inside of the 32mm hose attached to the pool/pump to a 16mm OD garden hose. If the garden hose won't stay in, push it through further, then wrap in tape and pull back to wedge the tape in place. Many...

Reduced the thread diameter to fit the Bestway F4030 outlet on my coleman 18ft round pool based on the model from https://www.thingiverse.com/thing:2469017 designed by johannesathome. Include a 4.5mm of the threaded section for test fitting.

Customized version of https://www.thingiverse.com/thing:2945382 Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing_id=2945382 This is a work in progress, I'll update when I can verify that it works! ...

This thing is a pool vacuum nozzle - the piece that attaches an aluminum telescopic pole connector to a variety of swimming pool cleaning implements. As this nozzle is designed for outdoor use you should take this into consideration when...

The human attaches a 1.5-inch garden hose directly to the filter system, providing a seamless connection for efficient water flow.

I modified the nozzle from Squbel, which has a tendency to stick to the pool floor, making it hard to maneuver. I drilled some holes into it to improve water flow. This nozzle prints well without any support material. ...Printing took around five hours...

Remixed the nozzle from squbel https://www.thingiverse.com/thing:224431 as it tends to suck itself to the pool ground and make movements complicated: I added some holes to allow more waterflow.Can be printed w/o supports. ...Took arround 5h on my Prusa...

... interface with a Festool vacuum, I added a 58mm adapter. This configuration delivers exceptional static pressure and performs remarkably well. I opted for the pool hose due to its affordability – a 35-inch hose costs approximately $42 at Home Depot.

This is an adapter for use with a standard pool vacuum hose and a 1" Schedule 40 PVC Pipe. The pool vacuum hose connectors are not standard plumbing fitting sizes, and my non-standard setup requires some... adapting. Just insert a 1" pipe into the...

It is a pool adapter to connect a Ø38 mm pipe into (for example) bestway pool intake pipe. ...

Created to adapt the 1-1/4 discharge hose ( https://www.homehardware.ca/en/24-sump-pump-hose-kit-with-1-14-adapter/p/3125059 ) to the outlet side of my Bestway pool. ... Should just slide on, using the original nut and an o-ring

A quick hose clip for pool vacuum hose. The inner diameter of the clip is 50mm. Two mounting holes fit #8 screw diameter. ...One mounting hole fits a 5/16" bolt diameter.

The bottom drain socket has a flow restrictor in it, this allows you to use this adapter, https://www.thingiverse.com/thing:5441996, to connect a vacuum to the skimmer and therefore leave the plumbing undisturbed. ...(Simplified remix attached that...

The original attachment for the vacuum was too expensive for a piece of plastic and I didn't want to buy another hose. I used 2 part epoxy to attach the pieces. I doubt cyanoacrylate would work well. Works perfect. No supports are needed and...

Dieser Adapter ist für meinen aufblasbaren Pool umkonstruiert worden. Der Schlauch Durchmesser ist 32mm. Der Anschlussdurchmesser ist 39mm. ... Viel Spaß damit.